32000
1.INSTALL TORQUE CONVERTER ASSEMBLY
Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)
Aligning the matchmarks on the transmission case and torque converter, and then engage the splines of the input shaft and turbine runner.
| *a | Matchmark |
Engage the splines of the stator shaft and stator while turning the torque converter.
| *a | Matchmark |
Turn the torque converter approximately 180°.
Turn the torque converter and align the matchmarks on the torque converter and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter.
| *a | Matchmark |
Do not push on the torque converter when aligning the matchmarks.
Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.
B = A + 1 mm (0.0394 in.) or more
33823A
2.INSTALL TRANSMISSION CONTROL CABLE BRACKET
Install the bracket with the 2 bolts.
3.INSTALL WIRE HARNESS CLAMP BRACKET
Install the front bracket LH with the bolt.
Install the rear bracket LH with the bolt.
Install the rear engine bracket with the bolt.
37109A
4.INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
Install the bracket with the bolt.
33490F
5.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)
Coat 4 new O-rings with ATF.
Install the 4 O-rings, transmission oil cooler spacer and transmission oil cooler to the automatic transmission assembly with the 3 bolts.
33490F
6.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)
Coat 4 new O-rings with ATF.
Install the 4 O-rings, transmission oil thermostat and transmission oil cooler to the automatic transmission assembly with the 3 bolts.
35000
7.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.) Centerpiece
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.
Install the transmission with the 10 bolts.
16278
8.CONNECT NO. 2 WATER BY-PASS PIPE (w/o Towing Hitch)
Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.
| *a | Stopper |
| *b | RH Side |
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
16278
9.CONNECT NO. 2 WATER BY-PASS PIPE (w/ Towing Hitch)
Connect the 2 oil cooler hoses to the transmission oil cooler.
| *a | Paint Mark |
Make sure the pinching portion of each clip is facing the direction shown in the illustration.
Make sure the paint portion of each hose is facing outward.
Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.
| *a | Stopper |
| *b | RH Side |
Pinching portion of clip shall be directed as shown in the illustration.
35104V
10.CONNECT BREATHER PLUG HOSE
Connect the 3 breather plug hoses to the harness clamp bracket.
11.CONNECT WIRE HARNESS AND CONNECTOR
Connect the park/neutral start switch connector, 2 transmission wire connectors and 2 speed sensor connectors.
Push up the lever until the claw of the transmission wire connector makes a connection sound.
Connect the harness clamp with the bolt.
Connect the 3 connector clamps and 7 harness clamps.
Tilt up the automatic transmission.
Connect the ground cable with the bolt.
12371
12.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
Install the rear engine mounting insulator to the transmission with the 4 bolts.
51204
13.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.
32101A
14.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.
First install the black colored bolt and then the remaining 5 bolts.
33820B
15.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the control cable with a new clip and the nut.
When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the outside of the vehicle.
28100
16.INSTALL STARTER ASSEMBLY
37110
17.INSTALL PROPELLER SHAFT ASSEMBLY
37140
18.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
17410
19.INSTALL FRONT EXHAUST PIPE ASSEMBLY
20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
21.ADD AUTOMATIC TRANSMISSION FLUID
22.ADD ENGINE COOLANT
23.INSPECT FOR ENGINE COOLANT LEAK
24.ADJUST SHIFT LEVER POSITION
25.INSPECT SHIFT LEVER POSITION
26.INSPECT FOR EXHAUST GAS LEAK
51405A
27.INSTALL NO. 1 ENGINE UNDER COVER
28.RESET MEMORY