Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM27M0U _52 Drivetrain _049126 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0234153 AUTOMATIC TRANSMISSION ASSEMBLY A

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

U152409E02
0.625,2.667 0.719,3.104 0.719,3.104 0.823,3.104 true 1.396,2.323 1.469,2.688 1.469,2.688 1.573,2.688 true 3.135,0.344 3.292,0.542 0.156,0.198 10 false A 3.125,1.406 3.323,1.583 0.198,0.177 10 false *2 1.604,2.615 1.802,2.792 0.198,0.177 10 false *2 2.958,0.604 3.125,0.771 0.167,0.167 10 false *1 0.865,3.042 1.031,3.208 0.167,0.167 10 false *1

a.

Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)


b.
C150409E03
1.494,0.014 1.650,0.176 0.156,0.162 10 *a 0.746,0.502 1.435,0.141 1.435,0.141 0.808,0.757 false

Aligning the matchmarks on the transmission case and torque converter, and then engage the splines of the input shaft and turbine runner.

Text in Illustration
*a Matchmark


c.
C150410E04
1.454,0.031 1.617,0.190 0.163,0.159 10 *a 0.75,0.529 1.425,0.209 1.425,0.209 0.964,1.715 false

Engage the splines of the stator shaft and stator while turning the torque converter.

Text in Illustration
*a Matchmark

HINT:

Turn the torque converter approximately 180°.



d.
C150411E04
1.418,0.013 1.601,0.199 0.182,0.187 10 *a 0.746,0.502 1.352,0.181 1.352,0.181 0.712,1.061 false

Turn the torque converter and align the matchmarks on the torque converter and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter.

Text in Illustration
*a Matchmark

NOTICE:

Do not push on the torque converter when aligning the matchmarks.



e.
C193839E02
2.852,0.638 3.008,0.813 0.156,0.174 10 B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more



Hide 33823A 2.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the bracket with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the front bracket LH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the rear bracket LH with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Install the rear engine bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 33490F 4.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)

C161367

a.

Coat 4 new O-rings with ATF.


b.

Install the 4 O-rings, transmission oil cooler spacer and transmission oil cooler to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 33490F 5.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)

C161366

a.

Coat 4 new O-rings with ATF.


b.

Install the 4 O-rings, transmission oil thermostat and transmission oil cooler to the automatic transmission assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 35000 6.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C196694E05
1.039,0.954 1.216,1.113 0.177,0.159 10 *2 2.753,0.937 2.940,1.100 0.187,0.163 10 *1 1.682,1.041 2.707,1.041 false

Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.) Centerpiece


Text in Illustration
*1 Torque Converter Centerpiece
*2 Crankshaft


b.
U152431E01
2.91,3.754 3.041,3.909 0.131,0.156 10 A 2.723,3.914 2.845,4.069 0.122,0.155 10 B 2.237,4.369 2.359,4.524 0.122,0.155 10 B 0.787,3.931 0.909,4.086 0.122,0.155 10 B 1.245,4.367 1.367,4.521 0.122,0.155 10 B 0.647,3.57 0.778,3.726 0.131,0.156 10 A 0.744,2.849 0.875,3.004 0.131,0.156 10 A 1.414,2.287 1.546,2.443 0.131,0.156 10 A 2.061,2.299 2.192,2.454 0.131,0.156 10 A 2.778,2.94 2.909,3.096 0.131,0.156 10 A

Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.


c.

Install the transmission with the 10 bolts.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 16278 7.CONNECT NO. 2 WATER BY-PASS PIPE (w/o Trailer Towing System)

a.
U152339E02
1.573,3.271 1.552,3.219 false 1.531,3.115 1.521,3.104 false 1.594,3.26 1.552,3.156 false 1.594,3.198 1.531,3.063 false 1.594,3.146 1.542,3.021 false 1.615,3.115 1.552,2.99 false 1.625,3.083 1.563,2.948 false 1.594,2.948 1.573,2.917 false 2.708,0.427 1.906,0.219 true 1.458,2.677 1.729,2.865 0.271,0.188 10 false *b 1.719,0.135 1.906,0.333 0.188,0.198 10 false *a

Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
*a Stopper
*b RH Side

NOTICE:

Make sure the pinching portion of each clip is facing the direction shown in the illustration.



Hide 16278 8.CONNECT NO. 2 WATER BY-PASS PIPE (w/ Trailer Towing System)

a.
C162129E04
0.655,0.601 0.901,0.784 0.246,0.183 10 45° 0.408,0.849 0.653,1.032 0.246,0.183 10 45° 1.518,0.694 1.749,0.874 0.231,0.180 10 *a 0.642,1.338 1.483,0.82 false

Connect the 2 oil cooler hoses to the transmission oil thermostat.

Text in Illustration
*a Paint Mark

NOTICE:
·

Make sure the pinching portion of each clip is facing the direction shown in the illustration.

·

Make sure the paint portion of each hose is facing outward.




b.
U152311E02
1.625,3.26 1.604,3.208 false 1.583,3.104 1.573,3.094 false 1.646,3.25 1.604,3.146 false 1.646,3.188 1.583,3.052 false 1.646,3.135 1.594,3.021 false 1.656,3.104 1.604,2.979 false 1.677,3.073 1.615,2.938 false 1.635,2.938 1.625,2.906 false 2.688,0.365 1.875,0.156 true 1.521,2.635 1.792,2.823 0.271,0.188 10 false *b 1.656,0.063 1.865,0.26 0.208,0.198 10 true *a

Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
*a Stopper
*b RH Side

NOTICE:

Pinching portion of clip shall be directed as shown in the illustration.



Hide 35104V 9.CONNECT BREATHER PLUG HOSE

a.

Connect the breather plug hose to the harness clamp bracket.


Hide 10.CONNECT WIRE HARNESS AND CONNECTOR

a.
C353008

Connect the park/neutral start switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Connect the harness clamp with the bolt.

Torque:
8.2 N*m (84 kgf*cm, 73 in.*lbf)


c.

Connect the 3 connector clamps and 4 harness clamps.


d.

Tilt up the automatic transmission.


e.

Connect the ground cable with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 12371 11.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

Torque:
40 N*m (407 kgf*cm, 30 ft.*lbf)


Hide 51204 12.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


Hide 32101A 13.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

a.

Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

Torque:
53 N*m (535 kgf*cm, 39 ft.*lbf)

NOTICE:

First install the black colored bolt and then the remaining 5 bolts.



Hide 33820B 14.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
U152341E02
2.448,0.823 1.313,1.073 true 1.115,0.979 1.313,1.146 0.198,0.167 10 false *1 1.708,0.292 1.938,0.479 0.229,0.188 10 true *a

Connect the control cable with a new clip and the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 Bracket
*a Inside of Vehicle

NOTICE:

When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the outside of the vehicle.



Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 37110 16.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL