Home › Drivetrain › A760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM27M0U _52 Drivetrain _049128 A760E AUTOMATIC TRANSMISSION / TRANSAXLE _0234185 AUTOMATIC TRANSMISSION ASSEMBLY A

A760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

U115867E03
0.958,0.885 0.792,0.156 0.792,0.156 0.688,0.156 true 1.146,2.427 1.313,3.167 1.313,3.167 1.417,3.167 true 2.979,0.583 3.167,0.771 0.188,0.188 10 false *1 0.427,0.083 0.615,0.271 0.188,0.188 10 false *1 3.219,1.385 3.406,1.573 0.188,0.188 10 true *2 1.49,3.063 1.677,3.25 0.188,0.188 10 false *2 2.75,0.229 2.906,0.406 0.156,0.177 10 false A

a.

Using a vernier caliper and straightedge, measure dimension "A" between the transmission fitting surface of the engine*1 and the torque converter fitting surface of the drive plate*2 (step 1).


b.
C209686E04
0.615,0.417 1.083,0.188 1.083,0.188 0.708,0.667 true 1.125,0.021 1.354,0.208 0.229,0.188 10 false *a

Align the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.

Text in Illustration
*a Matchmark


c.
C209688E03
1.151,0.021 1.363,0.202 0.213,0.181 10 *a 0.613,0.403 1.094,0.159 1.094,0.159 0.937,1.7 false

Mesh the splines of the stator shaft and stator while turning the torque converter clutch.

Text in Illustration
*a Matchmark

HINT:

Turn the torque converter clutch approximately 180°.



d.
C210209E03
1.192,0.033 1.438,0.210 0.246,0.177 10 *a 0.613,0.418 1.135,0.186 1.135,0.186 0.71,0.662 false

Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to fit the key of the oil pump drive gear into the slot on the torque converter clutch.

Text in Illustration
*a Matchmark

NOTICE:

Do not push on the torque converter when aligning the matchmarks.



e.
C209690E01
2.264,0.551 2.414,0.718 0.150,0.167 10 B

Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that B is more than A (measured in step 1).

Standard distance:

A + 1 mm (0.0394 in.) or more



Hide 33823A 2.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the bracket with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

U152440E01
0.105,2.449 0.236,2.604 0.131,0.156 10 A 3.211,0.591 3.333,0.746 0.122,0.155 10 B 2.544,0.47 2.666,0.624 0.122,0.155 10 B 2.406,0 2.528,0.155 0.122,0.155 10 B 1.486,0.057 1.608,0.212 0.122,0.155 10 B

a.

Install the 5 wire harness clamp brackets with the 5 bolts.

Torque:
for bolt A : 60 N*m (612 kgf*cm, 44 ft.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C209692E03
2.768,0.95 2.965,1.108 0.197,0.157 10 *1 0.874,0.955 1.054,1.133 0.181,0.178 10 *2 1.561,1.05 2.707,1.05 false

Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)


Text in Illustration
*1 Torque Converter Centerpiece
*2 Crankshaft


b.
U152431E01
2.91,3.754 3.041,3.909 0.131,0.156 10 A 2.723,3.914 2.845,4.069 0.122,0.155 10 B 2.237,4.369 2.359,4.524 0.122,0.155 10 B 0.787,3.931 0.909,4.086 0.122,0.155 10 B 1.245,4.367 1.367,4.521 0.122,0.155 10 B 0.647,3.57 0.778,3.726 0.131,0.156 10 A 0.744,2.849 0.875,3.004 0.131,0.156 10 A 1.414,2.287 1.546,2.443 0.131,0.156 10 A 2.061,2.299 2.192,2.454 0.131,0.156 10 A 2.778,2.94 2.909,3.096 0.131,0.156 10 A

Confirm that the 2 knock pins are on the transmission contact surface of the engine block before transmission installation.


c.

Install the transmission with the 10 bolts.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33490F 5.INSTALL TRANSMISSION OIL COOLER ASSEMBLY

Hide 7.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the park/neutral position switch connector, transmission wire connector and 2 speed sensor connectors.

U152426

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Connect the harness clamp with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Attach the 4 connector clamps and 5 harness clamps.


d.

Tilt up the automatic transmission.


e.

Connect the ground cable with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 12371 8.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 51204 9.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


Hide 32101A 10.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
53 N*m (535 kgf*cm, 39 ft.*lbf)

NOTICE:

Install the black bolt first, and then the 5 silver bolts.



b.

Install the flywheel housing side cover.


Hide 33820B 12.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

U152183E02
2.573,0.708 1.438,0.948 true 1.219,0.875 1.396,1.042 0.177,0.167 10 false *1 1.833,0.125 2.031,0.292 0.198,0.167 10 true *a

a.

Connect the control cable with a new clip and the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 Bracket
*a Inside of Vehicle

NOTICE:

When connecting the cable to the transmission control shaft lever, make sure the L bracket of the cable faces the inside of the vehicle.



Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 37110 14.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL