Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)
RM27M0U _55 Steering _049129 STEERING COLUMN _0234196 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  INSTALLATION  


PROCEDURE

Hide 45250 1.INSTALL STEERING COLUMN ASSEMBLY

a.
C290070

Install the steering column with the bolt and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 45203 2.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.

Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.


b.
C155151E03
0.646,1.615 1.646,1.313 false 0.646,1.615 1.677,1.542 false 0.427,1.51 0.635,1.719 0.208,0.208 10 false *a

Install the bolt.

Text in Illustration
*a Matchmark

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C155150E03
1.385,1.385 0.635,1.823 false 0.646,1.813 1.719,1.542 false 0.448,1.823 1.448,2.146 1,0.323 10 true *a

Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

Text in Illustration
*a Matchmark


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.
C154524E03
1.229,0.938 0.969,1.708 false 1.073,1.01 0.969,1.688 false 0.896,1.74 1.271,1.948 0.375,0.208 10 false *a

Align the matchmarks on the steering column and steering intermediate shaft.

Text in Illustration
*a Matchmark


d.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


e.
C155149

Install the 3 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 87201 4.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

a.
C154523

Install the air duct with the bolt.


Hide 73900 5.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55046A 6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

Hide 67914 9.INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)

Hide 67914 10.INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)

Hide 84306 11.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.
C290110

Install the turn signal switch with spiral cable to the steering column with the clamp.


b.
C154522

Connect the 5 connectors to the turn signal switch with spiral cable.


Hide 45286B 12.INSTALL UPPER STEERING COLUMN COVER

a.
C290109

Attach the claw to install the upper steering column cover.


b.

Attach the 4 clips.


Hide 45287 13.INSTALL LOWER STEERING COLUMN COVER

a.
C290108

Attach the 2 claws to install the lower steering column cover.


b.

Install the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 45100 15.INSTALL STEERING WHEEL ASSEMBLY

a.
C290071E02
2.313,0.24 2.552,0.24 2.552,0.24 2.688,0.323 false 2.479,0.24 2.677,0.427 false 2.146,0.156 2.51,0.469 0.365,0.313 10 false *a

Align the matchmarks on the steering wheel and steering main shaft.

Text in Illustration
*a Matchmark


b.

Install the steering wheel set nut.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 16.INSPECT STEERING WHEEL CENTER POINT

Hide 45187 18.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 19.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).