A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
55345A
1.INSTALL NO. 1 INSTRUMENT PANEL CLIP
Attach the 2 claws to install the 2 No. 1 instrument panel clips.
55328A
2.INSTALL NO. 3 INSTRUMENT PANEL STAY
Attach the 3 claws to install the 3 No. 3 instrument panel stays.
55301
3.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
Set the instrument panel sub-assembly and attach the 5 claws.
Install the 2 nuts <C> and 3 bolts <B>.
Install the 2 bolts <G>.
| *1 | Bolt <G> | *2 | Bolt <B> |
| *2 | Nut <C> | - | - |
Connect each connector and attach each wire harness clamp.
| *A | w/ Automatic Light Control System | *B | w/ Front Center Speaker |
86160P
4.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH
55409A
5.INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Attach the 3 clips and 2 claws to install the instrument panel speaker panel sub-assembly.
86160
6.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH
55409F
7.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Use the same procedure described for the instrument panel speaker panel sub-assembly.
62212
8.INSTALL FRONT PILLAR GARNISH LH
62312B
9.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
for Double Cab:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION)
for CrewMax:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>INSTALLATION)
for Regular Cab:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION)
62211
10.INSTALL FRONT PILLAR GARNISH RH
62311B
11.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
55405B
12.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
for 4WD:
Connect the connector.
Attach the 18 clips and wire harness clamp to install the center instrument cluster finish panel sub-assembly.
86140A
13.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
14.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY
Connect each connector.
Attach the 8 clips, 2 claws and guide to install the lower center instrument panel finish panel together with the air conditioning control assembly.
| *A | for Automatic Air Conditioning System | *B | for Manual Air Conditioning System |
| *1 | Protective Tape | *2 | Air Conditioning Control Assembly |
| *3 | Lower Center Instrument Panel Finish Panel | - | - |
55475A
15.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Attach the 3 claws and 4 clips to install the No. 2 instrument cluster finish panel garnish.
55045A
16.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH
Attach the 4 claws to install the lower instrument panel finish panel sub-assembly RH.
Install the 4 screws <F> and bolt <A>.
55317A
17.INSTALL INSTRUMENT SIDE PANEL RH
Attach the 4 guides and 3 claws to install the instrument side panel RH.
55064A
18.INSTALL NO. 4 INSTRUMENT REGISTER SUB-ASSEMBLY
Attach the 10 clips to install the No. 4 instrument register sub-assembly.
73990
19.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
55312
20.INSTALL LOWER INSTRUMENT PANEL
Attach the 3 claws to install the lower instrument panel.
Install the bolt <A> and screw <D>.
55607
21.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Attach the 2 guides, 4 claws and clip to install the No. 2 instrument panel under cover sub-assembly.
83100
22.INSTALL COMBINATION METER ASSEMBLY
55410C
23.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Attach the 6 clips to install the instrument cluster finish panel assembly.
Install the 2 clips.
55471A
24.INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT
Attach the 3 clips and claw to install the instrument cluster finish panel ornament.
55447C
25.INSTALL NO. 2 SWITCH HOLE BASE
Connect each connector.
Attach the 4 clips to install the No. 2 switch hole base.
45286B
26.INSTALL UPPER STEERING COLUMN COVER
45287
27.INSTALL LOWER STEERING COLUMN COVER
Attach the 2 claws to install the lower steering column cover.
While turning the steering wheel assembly to the right and left, install the 2 screws.
55474C
28.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Attach the 3 clips and 3 claws to install the No. 1 instrument cluster finish panel garnish.
73900
29.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
55046A
30.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
Connect the hood lock control cable to the hood lock control lever, rotate the hood lock control cable, and then slide and push the hood lock control cable into place.
Attach the 3 hooks to connect the hood lock control lever to the lower instrument panel finish panel sub-assembly LH.
Connect each connector.
Attach the 9 clips and 2 claws to install the lower instrument panel finish panel sub-assembly LH.
Install the 2 bolts <A>.
62112
31.INSTALL COWL SIDE TRIM BOARD LH
67914
32.INSTALL FRONT DOOR SCUFF PLATE LH
for Double Cab:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION)
for CrewMax:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>INSTALLATION)
for Regular Cab:
(See page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION)
62111C
33.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67913
34.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
55479B
35.INSTALL LOWER CENTER INSTRUMENT COVER
Attach the 2 guides and 2 clips to install the lower center instrument cover.
Install the 2 clips.
55318C
36.INSTALL INSTRUMENT SIDE PANEL LH
Attach the 4 guides and 3 claws to install the instrument side panel LH.
55061
37.INSTALL NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY
Attach the 4 clips to install the No. 1 instrument panel register sub-assembly.
38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
39. CHECK SRS WARNING LIGHT