Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Driver Side Pretensioner Squib Circuit  B1901/73  Open in Front Driver Side Pretensioner Squib Circuit  B1902/73  Short to GND in Front Driver Side Pretensioner Squib Circuit  B1903/73  Short to B+ in Front Driver Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and the front seat outer belt LH.

This circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code Detection Condition Trouble Area
B1900/73 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib LH circuit during primary check.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1901/73 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1902/73 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1903/73 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146254E48
0.738,3.108 3.472,3.278 2.735,0.170 10 Front Pretensioner Squib LH 2.983,1.516 3.190,1.702 0.207,0.186 10 L+ 4.781,1.628 5.090,1.814 0.309,0.186 10 PD+ 2.962,2.342 3.159,2.528 0.198,0.186 10 L- 4.78,2.468 5.079,2.655 0.299,0.186 10 PD- 3.221,1.498 3.363,1.668 0.142,0.170 10 1 3.236,2.348 3.392,2.504 0.156,0.156 10 2 4.584,1.531 4.698,1.694 0.114,0.163 10 2 4.584,2.371 4.705,2.534 0.121,0.163 10 1 4.758,4.118 4.998,4.302 0.239,0.184 10 P1 4.754,4.268 6.197,4.479 1.443,0.211 10 Center Airbag Sensor 0.738,2.955 1.125,3.107 0.387,0.152 10 P2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
U152386E02
2.021,3.688 2.448,3.844 false 0.917,0.656 0.927,1.583 false 0.156,2.229 2.552,2.583 2.396,0.354 10 false Front view of wire harness connector: (to Front Pretensioner Squib LH) 1.625,1.125 3.021,1.458 1.396,0.333 10 false Center Airbag Sensor 0.688,1.615 2.531,1.792 1.844,0.177 10 false Front Pretensioner Squib LH 1.01,0.729 1.146,0.885 0.135,0.156 10 false D 1.24,0.719 1.365,0.875 0.125,0.156 10 false C 2.177,3.146 3.01,3.313 0.833,0.167 10 false Connector C 2.469,3.792 2.802,3.958 0.333,0.167 10 false SST 0.479,3.563 0.729,3.729 0.25,0.167 10 false P2

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1900, B1901, B1902 or B1903 is not output (for Double Cab) A
DTC B1900, B1901, B1902 or B1903 is not output (for CrewMax) B
DTC B1900, B1901, B1902 or B1903 is output C
DTC B1900, B1901, B1902 or B1903 is not output (for Regular Cab) D

HINT:

Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.




D

2.CHECK CONNECTOR

A

B

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

C

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
U152387E01
0.168,2.468 2.542,2.832 2.375,0.363 10 Front view of wire harness connector: (to Front Pretensioner Squib LH) 1.691,1.078 3.086,1.259 1.394,0.181 10 Center Airbag Sensor 0.688,1.661 2.520,1.862 1.832,0.201 10 Front Pretensioner Squib LH 1.209,0.709 1.346,0.883 0.137,0.174 10 D 1.395,0.709 1.551,0.855 0.156,0.147 10 C 2.133,0.502 2.270,0.668 0.137,0.165 10 A 1.772,0.714 1.911,0.898 0.139,0.184 10 B 2.138,3.436 3.081,3.592 0.943,0.156 10 Connector C 2.187,3.879 2.392,4.021 0.205,0.142 10 L- 0.639,3.879 0.872,4.021 0.232,0.142 10 L+ 0.907,3.913 1.428,3.57 false 1.58,3.57 2.161,3.913 false 0.651,3.496 0.904,3.645 0.253,0.149 10 P2 0.714,0.032 1.384,0.211 0.670,0.179 10 Floor Wire 1.651,0.504 1.651,0.124 1.651,0.124 1.537,0.124 false

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
P2-1 (L+) - Body ground Ignition switch ON Below 1 V
P2-2 (L-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P2-1 (L+) - P2-2 (L-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P2-1 (L+) - P2-2 (L-) Always 1 MΩ or higher
P2-1 (L+) - Body ground
P2-2 (L-) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
C146268E17
0.542,1.219 0.854,0.771 false 0.031,1.26 1.219,1.646 1.188,0.385 10 false Front Pretensioner Squib LH 1.625,1.26 2.5,1.594 0.875,0.333 10 false Center Airbag Sensor 0.958,0.854 1.115,1.021 0.156,0.167 10 false D 1.094,0.844 1.25,1.021 0.156,0.177 10 false C

a.

Connect the connectors to the front seat outer belt RH and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1900, B1901, B1902 or B1903 is output (for Column Shift Type) A
DTC B1900, B1901, B1902 or B1903 is output (for Floor Shift Type) B
DTC B1900, B1901, B1902 or B1903 is not output C

HINT:

Codes other than DTC B1900, B1901, B1902 and B1903 may be output at this time, but they are not related to this check.




C

A

B