Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Passenger Side Pretensioner Squib Circuit  B1906/74  Open in Front Passenger Side Pretensioner Squib Circuit  B1907/74  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908/74  Short to B+ in Front Passenger Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor and the front seat outer belt RH.

This circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front pretensioner squib RH circuit.

DTC Code Detection Condition Trouble Area
B1905/74 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib RH circuit during primary check.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1906/74 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front pretensioner squib RH circuit for 2 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1907/74 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1908/74 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146254E47
0.738,3.113 3.102,3.283 2.364,0.170 10 Front Pretensioner Squib RH 2.961,1.516 3.160,1.702 0.199,0.186 10 R+ 4.801,1.628 5.119,1.814 0.318,0.186 10 PP+ 2.989,2.342 3.177,2.528 0.188,0.186 10 R- 4.808,2.468 5.116,2.655 0.309,0.186 10 PP- 3.246,1.51 3.388,1.680 0.142,0.170 10 1 3.236,2.348 3.392,2.504 0.156,0.156 10 2 4.584,1.531 4.698,1.694 0.114,0.163 10 4 4.584,2.371 4.705,2.534 0.121,0.163 10 5 4.758,4.118 4.998,4.302 0.239,0.184 10 Q1 4.754,4.268 6.197,4.479 1.443,0.211 10 Center Airbag Sensor 0.738,2.96 1.023,3.116 0.286,0.156 10 Q2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
U152388E02
2.135,3.417 2.521,4.042 false 0.531,2.198 2.938,2.542 2.406,0.344 10 false Front view of wire harness connector: (to Front Pretensioner Squib RH) 2.26,3.146 3.156,3.302 0.896,0.156 10 false Connector C 2.563,3.979 2.906,4.146 0.344,0.167 10 false SST 0.615,3.323 0.906,3.49 0.292,0.167 10 false Q2 1.458,1.323 2.854,1.479 1.396,0.156 10 false Center Airbag Sensor 0.229,0.052 1.427,0.417 1.198,0.365 10 false Front Pretensioner Squib RH 1,1.229 1.146,1.406 0.146,0.177 10 false D 1.188,1.229 1.344,1.406 0.156,0.177 10 false C

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1905, B1906, B1907 or B1908 is not output (for Regular Cab) A
DTC B1905, B1906, B1907 or B1908 is not output (for Double Cab) B
DTC B1905, B1906, B1907 or B1908 is not output (for CrewMax) C
DTC B1905, B1906, B1907 or B1908 is output D

HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.




D

2.CHECK CONNECTOR

A

B

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

C

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the No. 2 floor wire connector (on the front seat outer belt RH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
U152389E02
1.188,4.156 1.646,3.448 false 1.792,3.448 2.26,4.156 false 0.802,1.24 0.698,1.969 0.698,1.969 0.885,1.969 false 1.417,1.104 1.417,0.531 1.417,0.531 1.323,0.531 false 0.979,1.885 2.833,2.083 1.854,0.198 10 false Front Pretensioner Squib RH 1.698,1.406 3.094,1.625 1.396,0.219 10 false Center Airbag Sensor 1.125,1.313 1.26,1.479 0.135,0.167 10 false C 0.896,1.313 1.031,1.479 0.135,0.167 10 false D 1.521,1.313 1.646,1.469 0.125,0.156 10 false B 1.875,1.083 2,1.24 0.125,0.156 10 false A 2.188,3.448 2.99,3.594 0.802,0.146 10 false Connector C 2.292,4.073 2.469,4.219 0.177,0.146 10 false R- 0.938,4.073 1.135,4.219 0.198,0.146 10 false R+ 0.25,0.458 1.333,0.625 1.083,0.167 10 false No. 2 Floor Wire 0.74,3.531 1.031,3.677 0.292,0.146 10 false Q2 0.24,2.375 2.656,2.698 2.417,0.323 10 false Front view of wire harness connector: (to Front Pretensioner Squib RH)

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Q2-1 (R+) - Body ground Ignition switch ON Below 1 V
Q2-2 (R-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q2-1 (R+) - Q2-2 (R-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q2-1 (R+) - Q2-2 (R-) Always 1 MΩ or higher
Q2-1 (R+) - Body ground
Q2-2 (R-) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
C172068E12
1.063,1.156 0.823,1.469 false 0.271,1.479 1.458,1.844 1.188,0.365 10 false Front Pretensioner Squib RH 1.177,1.229 1.302,1.427 0.125,0.198 10 false D 1.313,1.229 1.458,1.417 0.146,0.188 10 false C 1.823,1.406 2.708,1.729 0.885,0.323 10 false Center Airbag Sensor

a.

Connect the connectors to the front seat outer belt RH and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1905, B1906, B1907 or B1908 is output (for Column Shift Type) A
DTC B1905, B1906, B1907 or B1908 is output (for Floor Shift Type) B
DTC B1905, B1906, B1907 or B1908 is not output C

HINT:

Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.




C

A

B