Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0210/33  Right Rear Wheel Speed Sensor Signal  C0215/34  Left Rear Wheel Speed Sensor Signal  C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1332/37  Open Circuit in Right Rear Wheel Speed Sensor Circuit  C1333/38  Open Circuit in Left Rear Wheel Speed Sensor Circuit  


DESCRIPTION

Refer to DTC C0200/31 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C0200/31).

DTC Code DTC Detection Condition Trouble Area
C0210/33
C0215/34
When any of following conditions detected:
1.

When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph).

2.

At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.

3.

When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).

4.

Pressure reduction mode of ABS system lasts for 28 seconds or more.

5.

When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors occurs twice or more for 30 seconds or more.

6.

Foreign matter adheres to sensor rotor.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1273/73
C1274/74
Detected only during test mode.
·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1277/77
C1278/78
Detected only during test mode.
·

Rear speed sensor (open)

·

Rear speed sensor circuit (open)


C1332/37
C1333/38
Open in rear speed sensor circuit continues for 0.15 seconds or more.
·

Rear speed sensor (open)

·

Rear speed sensor circuit (open)



HINT:
·

DTCs C0210/33 and C1332/37 are for the rear speed sensor RH.

·

DTCs C0215/34 and C1333/38 are for the rear speed sensor LH.



WIRING DIAGRAM

C159469E06
1.438,0.916 1.548,1.077 0.110,0.161 10 1 2.475,0.916 2.585,1.077 0.110,0.161 10 2 1.541,1.271 1.720,1.436 0.179,0.165 10 b3 1.533,1.416 3.050,1.604 1.517,0.188 10 Rear Speed Sensor RH 1.442,2.736 1.552,2.897 0.110,0.161 10 1 2.475,2.738 2.585,2.898 0.110,0.161 10 2 1.541,3.102 1.720,3.267 0.179,0.165 10 b4 1.533,3.247 3.050,3.435 1.517,0.188 10 Rear Speed Sensor LH 5.856,4.003 6.146,4.182 0.290,0.179 10 A17 5.828,4.153 6.966,4.327 1.137,0.174 10 Skid Control ECU 6.038,3.546 6.333,3.711 0.295,0.165 10 RL- 6.056,2.812 6.351,2.978 0.295,0.165 10 RL+ 5.782,3.634 6.002,3.799 0.221,0.165 10 37 5.782,2.91 6.002,3.076 0.221,0.165 10 36 5.763,1.822 5.947,1.964 0.184,0.142 10 42 5.763,1.098 5.947,1.240 0.184,0.142 10 43 6.052,0.991 6.370,1.147 0.318,0.156 10 RR+ 6.052,1.701 6.370,1.857 0.318,0.156 10 RR-

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Check the speed sensor signal in test mode after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.READ VALUE USING TECHSTREAM (RL/RR WHEEL SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List mode on the Techstream.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Wheel Speed Rear wheel speed sensor LH reading /
min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed Similar speed as indicated on speedometer
RR Wheel Speed Rear wheel speed sensor RH reading /
min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed Similar speed as indicated on speedometer


d.

Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.

OK:

The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.


HINT:

There is a tolerance of +/-10% in the speedometer indication.




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform a TEST MODE inspection and check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

No DTCs output.




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

10.REPLACE REAR SPEED SENSOR
4.CHECK REAR SPEED SENSOR INSTALLATION
a.
I044006E26
0.667,1.406 0.875,1.604 false 0.938,1.594 1.781,1.875 0.844,0.281 10 false No clearance 0.417,1.74 0.646,1.906 0.229,0.167 10 false OK 2.563,1.844 2.792,2.01 0.229,0.167 10 false NG

Check that the speed sensor installation bolt is tightened properly.

OK:

The installation bolt is tightened properly.




OK

5.CHECK REAR SPEED SENSOR

NG

5.CHECK REAR SPEED SENSOR
a.

Visually check the speed sensor for deformation and damage.

OK:

No deformation or damage.

There is no gap between the sensor and rear axle carrier.




OK

6.CHECK SPEED SENSOR TIP

NG

6.CHECK SPEED SENSOR TIP

b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.
U152487E02
2.094,1.75 1.969,2.052 true 2.25,1.75 2.396,2.021 true 1.177,1.74 0.875,2.01 true 1.333,1.75 1.438,2.01 true 0.135,0 2.531,0.552 2.396,0.552 10 false Front view of wire harness connector: (to Skid Control ECU) 0.094,2.24 2.49,2.74 2.396,0.5 10 false Front view of wire harness connector: (to Rear Speed Sensor) 0.615,2.01 0.948,2.198 0.333,0.188 10 false RR+ 2.365,2.083 2.698,2.271 0.333,0.188 10 false RL+ 1.385,2.052 1.719,2.24 0.333,0.188 10 false RR- 1.875,2.052 2.208,2.24 0.333,0.188 10 false RL- 0.115,3.094 0.323,3.26 0.208,0.167 10 false b3 1.823,3.125 2.031,3.292 0.208,0.167 10 false b4 0.115,0.833 0.396,1 0.281,0.167 10 false A17

Confirm that the skid control ECU connector and speed sensor connector are properly connected.


b.

Disconnect the A17 ECU connector.


c.

Disconnect the b3 and b4 sensor connectors.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A17-43 (RR+) - b3-2 Always Below 1 Ω
A17-42 (RR-) - b3-1
A17-43 (RR+) - Body ground Always 10 kΩ or higher
A17-42 (RR-) - Body ground


for LH:
Tester Connection Condition Specified Condition
A17-36 (RL+) - b4-2 Always Below 1 Ω
A17-37 (RL-) - b4-1
A17-36 (RL+) - Body ground Always 10 kΩ or higher
A17-37 (RL-) - Body ground




OK

8.CHECK REAR SPEED SENSOR (INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)

8.CHECK REAR SPEED SENSOR (INPUT VOLTAGE)
a.
U152147E02
0.083,0 2.458,0.313 2.375,0.313 10 false Front view of wire harness connector: (to Rear Speed Sensor) 0.115,0.771 0.323,0.948 0.208,0.177 10 false b3 1.833,0.771 2.042,0.948 0.208,0.177 10 false b4

Reconnect the A17 ECU connector.


b.

Disconnect the b3 and b4 sensor connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b3-2 - Body ground Ignition switch ON 5.5 to 20 V
b4-2 - Body ground




OK

9.RECONFIRM DTC

NG

9.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

10.REPLACE REAR SPEED SENSOR

B

10.REPLACE REAR SPEED SENSOR

NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B

END