Home › Vehicle Interior › AIR CONDITIONING › CONDENSER
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234419 CONDENSER A

AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88474 1.INSTALL COOLER DRYER

a.
E050386

Using pliers, install the cooler dryer.


b.
E344967

Apply a sufficient amount of compressor oil to the contact surfaces of a new O-ring and the cap.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the cap.


d.
I030086

Using a 14 mm hexagon socket wrench, install the cap to the modulator.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)


Hide 88460 2.INSTALL COOLER CONDENSER ASSEMBLY

a.
E283114E01
0.068,0 0.305,0.221 0.237,0.221 10 *A 0.068,2.183 0.305,2.404 0.237,0.221 10 *B

Install the cooler condenser assembly with the 2 bolts as shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

Text in Illustration
*A w/o Air Cooled Transmission Oil Cooler
*B w/ Air Cooled Transmission Oil Cooler


Hide 88710 3.CONNECT AIR CONDITIONER TUBE ASSEMBLY

a.

Remove the attached vinyl tape from the air conditioner tube assembly and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube assembly.


d.

Connect the air conditioner tube assembly to the cooler condenser assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

When tightening the bolt, do not allow any tools to contact the pipe.

·

When tightening the bolt, hold a part of the pipe near the connector.




Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:
·

When tightening the bolt, do not allow any tools to contact the pipe.

·

When tightening the bolt, hold a part of the pipe near the connector.




Hide 32907A 6.CONNECT OIL COOLER HOSE (w/ Air Cooled Transmission Oil Cooler)

a.
E281055E02
0.875,1 1.198,0.469 1.198,0.469 0.927,1.01 false 0.802,2.542 0.563,3.115 0.563,3.115 0.76,2.51 false 1.198,0.292 1.385,0.479 0.188,0.188 10 false *1 0.469,3.156 0.656,3.344 0.188,0.188 10 false *2

Connect the 2 oil cooler hoses and attach the 2 clips.

NOTICE:

Make sure the paint marks and pinching portion of each clip are facing the directions shown in the illustration.


Text in Illustration
*1 Blue Paint
*2 Pink Paint


Hide 52119A 7.INSTALL FRONT BUMPER COVER

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).