Home › Vehicle Interior › WINDOW / GLASS › WINDSHIELD GLASS
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234460 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


PROCEDURE

Hide 56116C 1.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Apply Primer G to the glass where the spacers will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install 2 new stoppers onto the glass as shown in the illustration.

B442896E01
1.073,0.5 1.26,0.5 1.26,0.5 1.26,1.427 false 1.875,0.344 1.708,0.344 1.708,0.344 1.708,1.375 false 1.948,1.427 1.948,2.292 false 5.177,1.427 5.177,2.292 false 6.031,0.396 5.865,0.396 5.865,0.396 5.865,1.427 false 5.115,0.458 5.302,0.458 5.302,0.458 5.302,1.385 false 0.24,0.083 0.917,0.271 0.677,0.188 10 false Backside: 0.125,0.417 1.063,0.573 0.938,0.156 10 false Ceramic Notch 0.198,1.333 0.333,1.51 0.135,0.177 10 false a 1.24,1.75 1.677,1.948 0.438,0.198 10 false Center 1.604,2.302 2.49,2.458 0.885,0.156 10 false Ceramic Line 4.771,2.333 5.656,2.49 0.885,0.156 10 false Ceramic Line 5.552,1.76 5.99,1.958 0.438,0.198 10 false Center 6.802,1.333 6.938,1.51 0.135,0.177 10 false a 1.938,0.271 3.031,0.458 1.094,0.188 10 false Windshield Glass 6.094,0.302 7.031,0.458 0.938,0.156 10 false Ceramic Notch 3.979,0.365 5.073,0.552 1.094,0.188 10 false Windshield Glass

Standard:
Area Specified Condition
a 8.5 mm (0.334 in.)



Hide 56115C 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

B442897E01
0.875,0.51 0.875,0.281 0.875,0.281 1.25,0.281 false 2.635,1.74 2.635,1.01 2.635,1.01 2.458,1.01 false 1.271,0.188 1.823,0.375 0.552,0.188 10 false Stopper 2.333,1.781 3.198,1.969 0.865,0.188 10 false Vehicle Body

a.

Install 2 new stoppers to the vehicle body as shown in the illustration.


Hide 56117D 3.INSTALL WINDSHIELD GLASS ADHESIVE DAM

a.

Apply Primer G to the glass where the glass adhesive dams will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from the adhesive part of the dam. While aligning the dam to the ceramic notch and dam reference line, install the dam (adhesive side) to the glass (Primer G area).

U151921E02
0.719,2.167 0.958,2.385 0.958,2.385 0.958,2.948 false 4.802,2.208 4.594,2.375 4.594,2.375 4.594,2.948 false 5.906,2.875 5.969,3.094 5.969,3.094 6.031,2.875 false 6.427,1.188 6.49,1.396 6.49,1.396 6.552,1.188 false 2.469,2.865 2.469,3.313 false 0.031,0 0.948,0.167 0.917,0.167 10 false Backside: 1.792,2.229 1.948,2.417 0.156,0.188 10 false A 1.438,2.167 1.594,2.354 0.156,0.188 10 false A 3.979,2.031 4.135,2.219 0.156,0.188 10 false A 3.625,2.094 3.781,2.281 0.156,0.188 10 false A 2.99,2.583 3.156,2.781 0.167,0.198 10 false B 3,2.979 3.167,3.167 0.167,0.188 10 false B 0.302,2.958 1.677,3.125 1.375,0.167 10 false Dam Reference Line 4.01,2.938 5.333,3.104 1.323,0.167 10 false Dam Reference Line 1.979,3.302 3.302,3.469 1.323,0.167 10 false Dam Reference Line 5.677,1.406 6.958,1.573 1.281,0.167 10 false Dam Reference Line 4.063,0.594 5.052,0.771 0.99,0.177 10 false Ceramic Notch 0.583,0.615 1.531,0.802 0.948,0.188 10 false Ceramic Notch 5.604,3.115 6.917,3.292 1.313,0.177 10 false Dam Reference Line 5.604,2.031 5.969,2.208 0.365,0.177 10 false B - B 5.625,0.333 6.167,0.542 0.542,0.208 10 false A - A 5.156,1.604 5.344,1.813 0.188,0.208 10 false a 0.302,1.542 0.49,1.75 0.188,0.208 10 false a

Standard:
Area Specified Condition
a 29.2 mm (1.15 in.)



Hide 4.INSTALL UPPER WINDSHIELD OUTSIDE MOULDING

B166397E01
0.034,0 0.910,0.214 0.876,0.214 10 Backside:

a.

Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Install the windshield outside moulding, as shown in the illustration.

NOTICE:

Do not drive the vehicle for the amount of time written in the table below.


Usage time frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



Hide 56111 5.INSTALL WINDSHIELD GLASS

a.
U151850E02
2.292,2.229 1.135,2.229 false 1.229,0.49 1.844,0.656 0.615,0.167 10 false Primer M 1.281,1.844 1.896,2.021 0.615,0.177 10 false Primer M 0.552,2.135 1.146,2.323 0.594,0.188 10 false Adhesive 0.552,4.375 1.146,4.552 0.594,0.177 10 false Primer M 1.531,0.063 2.375,0.26 0.844,0.198 10 false CORRECT 1.313,2.354 2.323,2.552 1.01,0.198 10 false INCORRECT

Using a brush, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

U151980E02
1.26,2.542 1.26,2.875 false 4.719,1.281 4.719,1.5 false 6.302,1.271 6.302,1.469 false 4.781,2.927 4.781,3.156 false 6.042,3.115 6.042,3.177 false 0.146,0.115 0.802,0.323 0.656,0.208 10 false Backside: 1.406,1.125 1.604,1.365 0.198,0.24 10 false A 2.667,1.125 2.813,1.292 0.146,0.167 10 false A 2.698,1.469 2.823,1.656 0.125,0.188 10 false A 1.375,1.5 1.583,1.698 0.208,0.198 10 false A 2.083,1.115 2.302,1.313 0.219,0.198 10 false B 2.083,1.49 2.302,1.688 0.219,0.198 10 false B 0.833,1.927 0.969,2.115 0.135,0.188 10 false C 0.49,1.865 0.615,2.052 0.125,0.188 10 false C 2.719,1.927 2.854,2.125 0.135,0.198 10 false C 2.031,2.688 2.167,2.885 0.135,0.198 10 false D 2.031,2.323 2.167,2.49 0.135,0.167 10 false D 3.073,1.865 3.208,2.063 0.135,0.198 10 false C 0.688,2.896 2.083,3.083 1.396,0.188 10 false Adhesive Center Line 3.865,1.5 5.208,1.656 1.344,0.156 10 false Adhesive Center Line 3.844,3.167 5.167,3.354 1.323,0.188 10 false Adhesive Center Line 5.448,3.167 6.771,3.344 1.323,0.177 10 false Adhesive Center Line 5.417,1.479 6.813,1.667 1.396,0.188 10 false Adhesive Center Line 3.844,0.344 4.219,0.521 0.375,0.177 10 false A - A 5.417,0.354 5.823,0.521 0.406,0.167 10 false B - B 5.417,2 5.792,2.156 0.375,0.156 10 false D - D 3.844,2.021 4.219,2.198 0.375,0.177 10 false C - C 0.729,3.438 1.302,3.635 0.573,0.198 10 false Primer G

HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage time frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the glass as shown in the illustration.

B171650E02
2.115,2.552 2.115,2.885 false 4.885,1.271 4.583,1.365 4.583,1.365 4.583,1.479 false 6.521,1.229 6.219,1.323 6.219,1.323 6.219,1.438 false 5,2.906 4.698,3 4.698,3 4.698,3.125 false 6.115,2.927 6.219,3.104 6.219,3.104 6.292,2.927 false 6.219,3.094 6.219,3.167 false 0.042,0 0.813,0.198 0.771,0.198 10 false Backside: 2.115,1.115 2.313,1.354 0.198,0.24 10 false A 3.375,1.083 3.552,1.271 0.177,0.188 10 false A 3.406,1.479 3.552,1.667 0.146,0.188 10 false A 2.073,1.51 2.281,1.708 0.208,0.198 10 false A 2.76,1.104 2.979,1.302 0.219,0.198 10 false B 2.771,1.51 2.99,1.708 0.219,0.198 10 false B 1.542,1.938 1.74,2.167 0.198,0.229 10 false C 1.188,1.854 1.385,2.083 0.198,0.229 10 false C 3.438,1.896 3.635,2.125 0.198,0.229 10 false C 2.729,2.677 2.896,2.854 0.167,0.177 10 false D 2.729,2.292 2.875,2.49 0.146,0.198 10 false D 3.781,1.823 3.979,2.052 0.198,0.229 10 false C 0.385,2.125 0.542,2.406 0.156,0.281 10 true a 0.302,3.344 0.49,3.531 0.188,0.188 10 false a 0.844,2.219 1.021,2.49 0.177,0.271 10 true b 6.167,2.115 6.323,2.281 0.156,0.167 10 false b 0.76,2.875 0.917,3.042 0.156,0.167 10 false b 1.625,2.906 3.021,3.094 1.396,0.188 10 false Adhesive Center Line 4.021,1.49 5.417,1.677 1.396,0.188 10 false Adhesive Center Line 4.021,3.177 5.417,3.365 1.396,0.188 10 false Adhesive Center Line 5.604,3.188 6.917,3.375 1.313,0.188 10 false Adhesive Center Line 5.604,1.469 7,1.656 1.396,0.188 10 false Adhesive Center Line 1.094,3.365 1.74,3.552 0.646,0.188 10 false Adhesive 1,3.354 1.083,3.542 0.083,0.188 10 false : 4.052,0.375 4.427,0.552 0.375,0.177 10 false A - A 5.615,0.354 5.99,0.531 0.375,0.177 10 false B - B 5.594,2.021 6,2.198 0.406,0.177 10 false D - D 4.031,2.021 4.427,2.208 0.396,0.188 10 false C - C 4.896,0.594 5.021,0.771 0.125,0.177 10 false c 6.5,0.573 6.656,0.729 0.156,0.156 10 false c 4.906,2.229 5.125,2.375 0.219,0.146 10 false c 5.677,2.479 5.896,2.625 0.219,0.146 10 false c

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 4.0 mm (0.157 in.)




d.
B166394E04
1.677,1.427 1.177,1.427 1.177,1.427 1.177,1.781 false 1.677,1.708 1.177,1.708 false 0.729,1.802 1.521,1.979 0.792,0.177 10 true Matchmark

Install the glass to the vehicle body.

i.

Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.


ii.

Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.




iii.

Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.



e.

w/ Windshield Deicer:

Install the clip and connect the connector.


Hide 75534 6.INSTALL WINDSHIELD MOULDING OUTSIDE

B166398E01
0.047,0 0.946,0.246 0.899,0.246 10 Backside: 1.606,3.019 1.831,3.231 0.225,0.211 12 a

a.

Install the windshield outside moulding, as shown in the illustration.


b.

Apply Primer G to the windshield outside moulding area "a" shown in the illustration.


Hide 56111 7.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 75561 8.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

Hide 75552 9.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

Hide 75551 10.INSTALL ROOF DRIP SIDE FINISH MOULDING RH

HINT:

Use the same procedures described for the LH side.


Hide 75554A 11.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

Hide 75553A 12.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 13.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the roof headlining to its original position.


Hide 74610A 15.INSTALL ASSIST GRIP SUB-ASSEMBLY

a.

for Regular Cab, for Double Cab:

Install the assist grip (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


b.

for CrewMax:

Install the assist grip (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>INSTALLATION).


Hide 74348 16.INSTALL VISOR HOLDER

a.

for Regular Cab:

Install the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION).


b.

for Double Cab, w/o Illumination:

Install the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


c.

for CrewMax, w/o Illumination:

Install the visor holder (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>INSTALLATION).


Hide 74320 17.INSTALL VISOR ASSEMBLY LH

a.

for Regular Cab:

Install the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION).


b.

for Double Cab:

Install the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


c.

for CrewMax:

Install the visor (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>INSTALLATION).


Hide 74310 18.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 81240 19.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 63650A 20.INSTALL ROOF CONSOLE BOX ASSEMBLY

a.

Install the roof console box (see page Vehicle Interior>INTERIOR>OVERHEAD CONSOLE BOX>INSTALLATION).


Hide 87810 21.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

a.

w/ EC Mirror:

Install the inner rear view mirror (see page Vehicle Interior>MIRROR>INNER REAR VIEW MIRROR>INSTALLATION).


b.

w/o EC Mirror:

Install the inner rear view mirror (see page Vehicle Interior>MIRROR>INNER REAR VIEW MIRROR>INSTALLATION).


Hide 87834 22.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 62312B 25.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55781E 27.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53867H 28.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 29.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 85222A 30.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85212A 31.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH