Home › Vehicle Interior › INTERIOR PANEL › INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type)
RM27M0U _58 Vehicle Interior _049163 INTERIOR PANEL _0234481 INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type) A

INTERIOR PANEL  INSTRUMENT PANEL SAFETY PAD(for Floor Shift Type)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 55301 3.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

a.

Set the instrument panel sub-assembly and attach the 5 claws.


b.

Install the 2 nuts <C> and 3 bolts <B>.


c.

Install the 2 bolts <G>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

B356780E02
5.115,5.458 5.313,5.615 0.198,0.156 10 false *1 5.885,5.427 6.063,5.583 0.177,0.156 10 true *1 6.458,3.135 6.635,3.292 0.177,0.156 10 false *2 4.052,4.521 4.229,4.677 0.177,0.156 10 true *2 3.125,4.49 3.302,4.646 0.177,0.156 10 true *2 2.885,4.781 3.063,4.938 0.177,0.156 10 false *3 1.198,4.906 1.375,5.063 0.177,0.156 10 false *3

Text in Illustration
*1 Bolt <G> *2 Bolt <B>
*3 Nut <C> - -


d.

for Automatic Air Conditioning System:

Attach the 2 claws to connect the cooler thermistor.


e.

Connect each connector and attach each wire harness clamp.

B355399E02
2.802,0.615 3.01,0.781 0.208,0.167 10 true *A 3.021,0.938 3.229,1.104 0.208,0.167 10 true *B 1.531,4.573 1.74,4.74 0.208,0.167 10 false *C

Text in Illustration
*A w/ Automatic Light Control System *2 w/ Front Center Speaker
*3 for Automatic Air Conditioning System - -


Hide 55409F 7.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Hide 62312B 9.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 11.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 55405B 12.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 86140A 13.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Hide 14.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY

Hide 55475A 15.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55045A 16.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH

Hide 55607 21.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55410C 23.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.

Attach the 6 clips to install the instrument cluster finish panel assembly.


b.

Install the 2 clips.


Hide 55471A 24.INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

a.
B355397

Attach the 3 clips and claw to install the instrument cluster finish panel ornament.


Hide 55447C 25.INSTALL NO. 2 SWITCH HOLE BASE

a.

Connect each connector.


b.
B355395

Attach the 4 clips to install the No. 2 switch hole base.


Hide 55474C 26.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 73900 27.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55046A 28.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

Hide 62111C 31.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67913 32.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 58811A 33.INSTALL FRONT CONSOLE BOX

a.

Install the front console box with the 5 screws <E>.


b.

Install the 2 clips and attach the connector.


Hide 58910C 34.INSTALL REAR CONSOLE BOX ASSEMBLY

a.

Install the rear console box assembly with the 2 screws <E> and 4 bolts <B>.


b.

Connect the 2 connectors.


Hide 58815A 35.INSTALL CONSOLE BOX CARPET

a.

Install the console box carpet.


Hide 58903A 36.INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY

a.

w/ Power Outlet Socket:

Attach the 2 wire harness clamps and connect the connector.


b.
B355390

Attach the 7 clips to install the rear console end panel sub-assembly.


Hide 58804A 37.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

a.

Attach the 12 clips to install the upper console panel sub-assembly.


Hide 58805C 38.INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

a.
B355387

Attach the 6 clips to install the upper rear console panel sub-assembly.


Hide 33504F 39.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

a.
B355385E01
0.464,1.654 0.666,1.824 0.202,0.170 10 *a 1.581,0.978 0.561,1.442 0.561,1.442 0.561,1.643 false

Twist the shift lever knob sub-assembly in the direction indicated by the arrow to install it.

HINT:
·

Tighten the shift lever knob sub-assembly until there is no rotational free-play.

·

If the leather portion of the knob is not facing forward, tighten the knob further until the leather portion faces forward.



Text in Illustration
*a Leather Portion


Hide 55061 41.INSTALL NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY

Hide 42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 43.RESTORE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

a.

Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter (See page Steering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS).