Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › 2020.08–2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438037 TRANSMISSION CONTROL CABLE A

K320 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446031N08
1.938,1.083 2.271,1.083 false 1.958,1.771 2.292,1.771 false 2.031,2.583 2.365,2.583 false 6.448,0.25 6.781,0.25 false 6.417,0.698 6.75,0.698 false 4.563,1.073 4.896,1.073 false 5.677,2.208 6.01,2.208 false 6,0.094 6.615,0.365 0.615,0.271 18 false 1, 2 6.24,0.542 6.521,0.896 0.281,0.354 18 false 3 2.333,0.948 2.615,1.302 0.281,0.354 18 false 4 2.385,1.615 2.667,1.969 0.281,0.354 18 false 5 2.438,2.427 2.719,2.781 0.281,0.354 18 false 6 4.385,0.917 4.667,1.271 0.281,0.354 18 false 7 6.052,2.063 6.333,2.417 0.281,0.354 18 false 8 5.385,1.583 5.635,1.75 0.25,0.167 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SECURE VEHICLE - (Click here) - -
3 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
5 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
6 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
7 ECM 89661 - - -
8 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C446898N02
1.479,0.458 1.813,0.458 false 5.844,0.406 6.177,0.406 false 4.802,2.094 5.135,2.094 false 3.469,1.563 3.833,1.917 3.833,1.917 4,1.917 false 1.552,1.521 1.885,1.521 false 4.417,5.25 4.75,5.25 false 3.521,3.396 3.677,3.635 3.677,3.635 3.844,3.635 false 2.208,4.76 2.365,4.51 2.365,4.51 2.531,4.51 false 1.083,3.031 1.417,3.031 false 1.198,0.333 1.75,0.688 0.552,0.354 18 false 11 4.5,1.094 4.813,1.292 0.313,0.198 10 false x4 6.198,0.271 6.75,0.625 0.552,0.354 18 false 12 5.156,2.969 5.469,3.219 0.313,0.25 10 false x2 2.906,2.448 3.219,2.646 0.313,0.198 10 false x2 2.104,3.688 2.417,3.885 0.313,0.198 10 false x2 2.344,3.906 2.656,4.104 0.313,0.198 10 false x2 5.052,3.281 5.365,3.479 0.313,0.198 10 false x2 4.24,3.51 5.552,4.125 1.313,0.615 18 false 10 4.292,1.802 4.667,2.156 0.375,0.354 18 false 14 4.125,5.135 4.479,5.49 0.354,0.354 18 false 13 2.573,4.375 2.927,4.729 0.354,0.354 18 false 9 0.958,2.948 1.115,3.146 0.156,0.198 10 false ● 4.677,2 4.833,2.198 0.156,0.198 10 false ● 1.938,1.427 2.094,1.625 0.156,0.198 10 false ● 2.5,5.104 2.813,5.302 0.313,0.198 10 false x2 1.552,5.188 1.865,5.385 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

9 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
10 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -
11 FRONT NO. 1 FLOOR HEAT INSULATOR 58151 - - -
12 FRONT NO. 2 FLOOR HEAT INSULATOR 58153 - - -
13 REAR CONSOLE BOX ASSEMBLY 58910C - - -
14 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.SECURE VEHICLE

a.
C432457N01
0.417,0.083 0.698,0.438 0.281,0.354 18 false i

i.

Fully apply the parking brake and chock a wheel.

CAUTION:
·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.





Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 51447D 9.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58151 11.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C445361


Hide 58153 12.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

a.
C446034

i.

Remove 4 nuts and front No. 2 floor heat insulator from the vehicle body.



Hide 58910C 13.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 14.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C446891

i.

Move the shift lever to N.



b.
C431098C02
5.719,2.094 5.177,2.333 true 4.969,2.25 5.177,2.438 0.208,0.188 10 true *1 5.979,2.438 6.177,2.583 0.198,0.146 10 true *a 0.896,0.615 1.031,0.927 0.135,0.313 18 true i 3.938,0.135 4.167,0.448 0.229,0.313 18 true ii
*1 Lock Nut - -
*a Counterclockwise - -


i.

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


ii.

Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.



c.
C431092C02
2.073,2.063 2.385,1.802 false 2.417,1.719 2.729,1.875 0.313,0.156 10 false *1 3.104,2.719 3.417,2.875 0.313,0.156 10 false *a 0.656,0.135 0.833,0.385 0.177,0.25 18 true i 3.917,1.167 4.094,1.417 0.177,0.25 18 true ii
*1 Clip - -
*a 45° to 60° - -


i.

While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


ii.

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.



d.
C446900N01
0.323,0.073 0.688,0.354 0.365,0.281 18 true i, ii 3.969,0.073 4.198,0.344 0.229,0.271 18 true iii

i.

Remove the nut.


ii.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


iii.

Remove the 2 nuts and transmission control cable assembly from the vehicle body.