|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
| *A | w/ Stud Bolt | *B | w/o Stud Bolt |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 22 | EXHAUST MANIFOLD | 17141 | ( )
|
- | - |
| 23 | MANIFOLD STAY | 17118 | ( )
|
- | - |
| 24 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | 17167 | ( )
|
- | - |
| 25 | AIR FUEL RATIO SENSOR | 89467B | ( )
|
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| * | For use with SST | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.
Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.
Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.
16281
2.INSTALL NO. 4 WATER BY-PASS HOSE
11452D
3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Install the new O-ring to the engine oil level dipstick guide.
Apply a light coat of engine oil to a new O-ring.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.
23845G
6.INSTALL FUEL DELIVERY INSULATOR
82126A
7.INSTALL NO. 6 ENGINE WIRE
82219C
8.INSTALL SENSOR WIRE
Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Engage the 2 clamps.
Connect the 4 connectors.
9.INSTALL WATER BY-PASS PIPE ASSEMBLY
23470
10.INSTALL FUEL PUMP LIFTER ASSEMBLY
23802B
11.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY
23902
12.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY
Connect the No. 2 fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the fuel pipe clamp to the fuel tube connector.
23901
13.INSTALL FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
17177
14.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
25624
16.INSTALL EGR VALVE ADAPTER
Using an 8 mm socket wrench, install the EGR valve adapter with the bolt.
25680
18.INSTALL EGR COOLER ASSEMBLY
12262
19.INSTALL NO. 2 VENTILATION HOSE
23820
20.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
22030
21.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY