|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | * | For use with a union nut wrench |
| ● | Non-reusable part |
|
Lithium soap base glycol grease |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | 45260 | ( )
|
- | - |
| 9 | COLUMN HOLE COVER SILENCER SHEET | 45259A | - | - | - |
| 10 | NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY | 55606 | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| *1 | CONNECTOR | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
44785C
1.INSTALL BRAKE BOOSTER GASKET
47210L
2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Install the brake booster with master cylinder assembly with the 4 nuts.
Tighten the nuts in the order shown in the illustration.
| *a | ECU Connector |
| *b | Connector |
| *c | Boot |
| *d | Brake Master Cylinder Push Rod Clevis |
| *e | Brake Master Cylinder Reservoir Assembly |
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.
Do not kink or damage the brake lines.
Be careful not to allow brake fluid to enter the connector.
If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.
5.CONNECT BRAKE LINE
|
|
| *a | Torque Wrench Fulcrum Length | - | - |
Using a union nut wrench, connect the brake line to the front flexible hose.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
Using a union nut wrench, connect the brake line to the front No. 2 brake tube way.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
47372
6.INSTALL NO. 2 BRAKE TUBE CLAMP
47371B
7.INSTALL NO. 6 BRAKE TUBE CLAMP
45259A
9.INSTALL COLUMN HOLE COVER SILENCER SHEET
55606
10.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
82111
11.CONNECT ENGINE ROOM MAIN WIRE
|
Lock the lock lever |
|
Connect the connector |
Engage the clamp.
Install the engine room main wire with the bolt.
Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.
Make sure that the connector is locked securely.
Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.
Connect the connector to the brake master cylinder reservoir assembly.
Engage the clamp.
Connect the connector.
G9200
12.INSTALL INVERTER WITH CONVERTER ASSEMBLY
13. UPDATE ECU SECURITY KEY
14.BLEED BRAKE LINE
15.INSPECT AND ADJUST BRAKE PEDAL
16.PERFORM INITIALIZATION AND CALIBRATION
17. CHECK FOR CLEAR DTCS