Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › from 2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438037 TRANSMISSION CONTROL CABLE A

K320 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446031N08
1.938,1.083 2.271,1.083 false 1.958,1.771 2.292,1.771 false 2.031,2.583 2.365,2.583 false 6.448,0.25 6.781,0.25 false 6.417,0.698 6.75,0.698 false 4.563,1.073 4.896,1.073 false 5.677,2.208 6.01,2.208 false 6,0.094 6.615,0.365 0.615,0.271 18 false 1, 2 6.24,0.542 6.521,0.896 0.281,0.354 18 false 3 2.333,0.948 2.615,1.302 0.281,0.354 18 false 4 2.385,1.615 2.667,1.969 0.281,0.354 18 false 5 2.438,2.427 2.719,2.781 0.281,0.354 18 false 6 4.385,0.917 4.667,1.271 0.281,0.354 18 false 7 6.052,2.063 6.333,2.417 0.281,0.354 18 false 8 5.385,1.583 5.635,1.75 0.25,0.167 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SECURE VEHICLE - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
5 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
6 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
7 ECM 89661 - - -
8 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C462303N02
2.594,2.625 2.927,2.625 false 3.833,0.979 4.167,0.979 false 2.406,2.479 2.688,2.833 0.281,0.354 18 false 9 4.229,0.833 4.583,1.177 0.354,0.344 18 false 10 1.094,1.854 1.406,2.052 0.313,0.198 10 false x2 2.625,1.615 2.938,1.813 0.313,0.198 10 false x2 3.198,3.021 3.51,3.219 0.313,0.198 10 false x2 5.021,2.969 5.333,3.167 0.313,0.198 10 false x2 0.083,0.083 0.458,0.323 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

9 FRONT FLOOR COVER LH 58166A - - -
10 FRONT FLOOR COVER RH 58165C - - -

*A for TMMF Made - -

C462304N02
1.833,0.167 4.417,1.667 2.583,1.5 4.417,0.167 7,1.667 2.583,1.5 0.333,4.083 3.083,5.667 2.75,1.583 3.083,4.083 5.833,5.667 2.75,1.583 3.531,3.146 3.771,3.427 3.771,3.427 3.938,3.427 false 2.969,0.635 2.813,0.385 2.813,0.385 2.635,0.385 false 0.896,0.656 1.156,0.323 1.156,0.323 1.313,0.323 false 5.26,1.906 5.594,1.906 false 1.542,2.781 1.875,2.781 false 5.51,0.656 5.354,0.406 5.354,0.406 5.177,0.406 false 4.219,4.417 4.5,4.24 4.5,4.24 4.667,4.24 false 1.24,4.688 1.521,4.51 1.521,4.51 1.688,4.51 false 4.146,4.99 4.427,5.208 4.427,5.208 4.594,5.208 false 2.333,0.25 2.75,0.615 0.417,0.365 18 false 15 1.365,0.188 1.708,0.531 0.344,0.344 18 false 14 4.281,3.313 4.656,3.656 0.375,0.344 18 false 13 1.74,4.375 2.115,4.719 0.375,0.344 18 false 11 4.729,4.115 5.104,4.479 0.375,0.365 18 false 12 2.875,1.302 3.188,1.5 0.313,0.198 10 false x4 4.875,0.271 5.292,0.625 0.417,0.354 18 false 15 5.448,1.302 5.76,1.5 0.313,0.198 10 false x3 5.646,1.813 5.823,2.031 0.177,0.219 10 false ● 1.917,2.688 2.094,2.906 0.177,0.219 10 false ● 1.917,0.25 2.292,0.49 0.375,0.24 12 false *A 3.167,4.167 3.542,4.406 0.375,0.24 12 false *B 5.177,2.74 5.49,2.938 0.313,0.198 10 false x2 5.042,3.083 5.354,3.281 0.313,0.198 10 false x2 2.375,3.76 2.688,3.958 0.313,0.198 10 false x2 2.135,3.5 2.448,3.698 0.313,0.198 10 false x2 1.031,5.375 1.344,5.573 0.313,0.198 10 false x2 1.667,5.031 1.979,5.229 0.313,0.198 10 false x2 3.74,5.365 4.052,5.563 0.313,0.198 10 false x4 4.5,4.708 4.813,4.906 0.313,0.198 10 false x2 4.667,5.073 5.021,5.417 0.354,0.344 18 false 11 0.417,4.167 0.792,4.406 0.375,0.24 12 false *A 4.5,0.25 4.875,0.49 0.375,0.24 12 false *B

Procedure Part Name Code
Z101186

Z101188

Z101187

11 CENTER NO. 4 ENGINE UNDER COVER 51447D - - -
12 CENTER NO. 1 FLOOR BRACE 57543C - - -
13 FRONT EXHAUST PIPE ASSEMBLY 17410 (Click here) - -
14 FRONT NO. 1 FLOOR HEAT INSULATOR 58151 - - -
15 FRONT NO. 2 FLOOR HEAT INSULATOR 58153 - - -

*A for TMC Made *B for TMMF Made
● Non-reusable part - -

C462305N02
4,2.396 4.333,2.396 false 2.188,1.958 2.521,1.958 false 2.771,0.844 3.104,0.844 false 4.646,2.281 5.01,2.625 0.365,0.344 18 false 17 2.458,0.688 2.875,1.042 0.417,0.354 18 false 16 3.771,3.094 4.083,3.292 0.313,0.198 10 false x2 2.583,1.865 2.781,2.063 0.198,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

16 REAR CONSOLE BOX ASSEMBLY 58910C - - -
17 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.SECURE VEHICLE

a.
C432457N01
0.417,0.083 0.698,0.438 0.281,0.354 18 false i

i.

Fully apply the parking brake and chock a wheel.

CAUTION:
·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.





Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 58166A 9.REMOVE FRONT FLOOR COVER LH (for TMMF Made)

Hide 58165C 10.REMOVE FRONT FLOOR COVER RH (for TMMF Made)

a.

Perform the same procedure as for the LH side.


Hide 51447D 11.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 57543C 12.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 17410 13.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Z101186

Click here(Click here)

Hide 58151 14.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C445361


Hide 58153 15.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

a.
C462306C01
0.167,0.094 0.417,0.333 0.25,0.24 12 false *A 3.583,0.094 3.833,0.333 0.25,0.24 12 false *B
*A for TMC Made *B for TMMF Made



Hide 58910C 16.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 17.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

Z101186

NOTICE:

Before removing the transmission control cable assembly, make sure the shift lever is N.



a.
C462310C01
5.375,1.313 5.74,1.448 false 5.792,1.375 6.104,1.531 0.313,0.156 10 false *1 4.958,1.406 5.167,1.604 0.208,0.198 10 true *a 0.167,0.063 0.448,0.417 0.281,0.354 18 false i 4.219,0.083 4.5,0.438 0.281,0.354 18 false ii
*1 Lock Nut - -
*a Counterclockwise - -


i.

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


ii.

Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, separate the transmission control cable assembly from the transmission floor shift assembly.

NOTICE:

Do not rotate the lock nut excessively as the interior spring may come off and the transmission control cable assembly will not be reusable.




b.
C431092C02
2.073,2.063 2.385,1.802 false 2.417,1.719 2.729,1.875 0.313,0.156 10 false *1 3.104,2.719 3.417,2.875 0.313,0.156 10 false *a 0.656,0.135 0.833,0.385 0.177,0.25 18 true i 3.917,1.167 4.094,1.417 0.177,0.25 18 true ii
*1 Clip - -
*a 45° to 60° - -


i.

While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


ii.

Remove the clip and separate the transmission control cable assembly from the No. 1 transmission control cable bracket.



c.
C446900N01
0.323,0.073 0.688,0.354 0.365,0.281 18 true i, ii 3.969,0.073 4.198,0.344 0.229,0.271 18 true iii

i.

Remove the nut.


ii.

Disengage the guide to separate the transmission control cable assembly from the vehicle body.


iii.

Remove the 2 nuts and transmission control cable assembly from the vehicle body.