Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System)  


DESCRIPTION

Depending on the malfunction, the skid control ECU prohibits operation of the electronically controlled brake system to protect components and prevent incorrect operation when DTCs are stored.

If the switching solenoid is disabled due to prohibition of the electronically controlled brake system, the response of the brake pedal changes and braking performance is reduced.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY



PROCEDURE

1.PRE-INSPECTION
a.

Check the conditions at the time the problem occurred.

i.

Whether a warning light illuminated or the buzzer sounded.


ii.

Road surface condition when the problem occurred and just before the problem occurred.


iii.

When the problem occurred and how many times the brake pedal was depressed before the problem occurred.


iv.

Frequency of the abnormal brake pedal response.



Result:
Proceed to
NEXT



NEXT

2.CHECK DTC AND FREEZE FRAME DATA
2.CHECK DTC AND FREEZE FRAME DATA
a.

Using the GTS, check DTCs and Freeze Frame Data.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B


HINT:
·

If there are currently no warnings and the brake pedal travel is not excessive, DTCs may have been cleared after the system returned to normal.

·

If the brake pedal response returned to normal and there are currently no warnings, the system is normal.





A

3.CHECK BRAKE PEDAL

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK BRAKE PEDAL
a.

While depressing the brake pedal by hand, check the installation condition of the brake pedal stroke sensor assembly and brake pedal, and check for mechanical malfunctions.



Result:
Proceed to
NEXT



NEXT

4.CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
4.CHECK VEHICLE CONTROL HISTORY (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
a.

Using the GTS, check for Vehicle Control History (RoB).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>VEHICLE CONTROL HISTORY (RoB)

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 1055

Result:
Result Proceed to
There is no vehicle control history (RoB) for when the electronically controlled brake system and electric parking brake system were suspended. A
There is vehicle control history (RoB) for when the electronically controlled brake system and/or electric parking brake system were suspended. B



A

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY (RoB)

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>VEHICLE CONTROL HISTORY (RoB)

NOTICE:

After performing troubleshooting and repair regarding vehicle control history (RoB), clear the vehicle control history (RoB).



5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.

Check the brake booster with master cylinder assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (for HV Model TMMF Made)>ON-VEHICLE INSPECTION

OK:

The brake booster with master cylinder assembly is normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR BRACKET ASSEMBLY

NG