Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E31
4.483,0.815 6.151,0.978 1.668,0.163 10 Camshaft Position Sensor 4.483,1.325 6.216,1.485 1.733,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 4.811,3.976 3.213,0.229 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.483,1.827 5.808,1.981 1.325,0.154 10 Mass Air Flow Meter 4.483,2.854 6.827,3.042 2.344,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.031,2.511 1.547,0.167 10 Throttle Position Sensor 4.483,3.353 5.938,3.506 1.455,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 7.005,4.480 3.346,0.264 10 VVT Controller (Camshaft Timing Gear Assembly) 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in camshaft timing oil control valve assembly circuit
(1 trip detection logic)
·

Open or short in camshaft timing oil control valve assembly circuit

·

Camshaft timing oil control valve assembly

·

ECM



HINT:

These DTCs relate to the camshaft timing oil control valve assembly.


MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Wait 5 seconds or more.

6.

Enter the following menus: Powertrain / Engine and ECT / DTC.

7.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



8.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

9.

Input the DTC: P0010.

10.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A381768E01
1.615,0.583 1.771,0.781 0.156,0.198 10 false 1 1.625,1.208 1.781,1.406 0.156,0.198 10 false 2 0.646,1.667 1.01,1.865 0.365,0.198 10 false B63 0.646,1.823 2.427,2.219 1.781,0.396 10 false Camshaft Timing Oil Control Valve assembly 4.781,0.698 5.177,0.896 0.396,0.198 10 false B84 4.781,1.344 5.177,1.542 0.396,0.198 10 false B84 4.781,0.49 5.104,0.677 0.323,0.188 10 false 100 4.781,1.125 5.104,1.313 0.323,0.188 10 false 123 5.156,0.573 5.583,0.792 0.427,0.219 10 false OC1+ 5.167,1.219 5.604,1.406 0.438,0.188 10 false OC1- 5.573,2.042 6.031,2.24 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTC
a.

Clear DTCs after recording the freeze frame data and DTCs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).


b.

Turn the ignition switch off.


c.

Start the engine and allow it to idle. Then check for DTCs.


d.

Check that P0010 is not output.

OK:

P0010 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B63-1 - B84-100 (OC1+) Always Below 1 Ω
B63-2 - B84-123 (OC1-) Always Below 1 Ω
B63-1 or B84-100 (OC1+) - Body ground Always 10 kΩ or higher
B63-2 or B84-123 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR