Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0133  Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).

HINT:

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No. DTC Detection Condition Trouble Area
P0133 While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich to lean or from lean to rich is 1 second or more (2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor heater (sensor 1)

·

No. 1 integration relay (EFI MAIN relay)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM



MONITOR DESCRIPTION

The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio close to the stoichiometric air-fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The sensor detects oxygen levels in the exhaust gas and sends a signal to the ECM.

The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The heated oxygen sensor generates waveforms of a voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the heated oxygen sensor voltage is 0.45 V or more, the ECM judges that the air-fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air-fuel ratio is lean. The ECM monitors the response feature of the heated oxygen sensor. If the response time of the heated oxygen sensor status change from rich to lean (or vice versa) becomes longer, the ECM interprets this as a malfunction in the heated oxygen sensor and stores a DTC.

A084946E19
5.125,0.771 4.271,0.958 false 0.375,0.073 2.031,0.313 1.656,0.24 10 false Frequency Condition 0.75,1.958 1.75,2.354 1,0.396 10 false Heated Oxygen Sensor Voltage 2.354,3.323 4.292,3.563 1.938,0.24 10 false Lean side frequency 3.365,0.229 4.25,0.448 0.885,0.219 10 false One Cycle 5.177,0.688 6.802,0.885 1.625,0.198 10 false Rich side frequency 5.448,2.031 6.052,2.24 0.604,0.208 10 false 0.45 V

A106048E09
0.969,0.438 2.677,0.635 1.708,0.198 10 false Slow Slope Condition 3.865,1.083 4.375,1.281 0.51,0.198 10 false RICH 4.521,2.417 5.063,2.615 0.542,0.198 10 false LEAN 2.729,3.052 6.24,3.26 3.51,0.208 10 false LEAN to RICH, RICH to LEAN Time Definition 2.49,0.271 4.198,0.469 1.708,0.198 10 false LEAN to RICH Time 4.51,0.281 6.219,0.479 1.708,0.198 10 false RICH to LEAN Time 0.052,0.781 1.177,1.344 1.125,0.563 10 false Heated Oxygen Sensor (Sensor 1) Voltage 1.073,1.354 1.531,1.552 0.458,0.198 10 false 0.5 V 1.01,1.833 1.521,2.031 0.51,0.198 10 false 0.45 V 1.094,2.292 1.542,2.479 0.448,0.188 10 false 0.4 V 6.625,3.042 7.042,3.24 0.417,0.198 10 false Time

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related) Mass air flow meter, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Duration that vehicle has run with the following conditions A and B 15 seconds or more
A. Vehicle speed 40 km/h (24 mph) or more
B. Engine speed 900 rpm or more
Time after engine start 120 seconds or more
Idle ON
Fuel system status Closed loop
Vehicle speed Less than 5 km/h (3 mph)
Engine coolant temperature 75°C (167°F) or more

TYPICAL MALFUNCTION THRESHOLDS

One of the following conditions is met -
Average of switch time from lean to rich* 1 second or more
Average of switch time from rich to lean* 1 second or more
* Lean 0.4 V or lower
* Rich 0.5 V or higher

CONFIRMATION DRIVING PATTERN

A257482E04
1.656,1.885 1.906,2.042 0.25,0.156 10 false [A] 2.208,1.948 2.427,2.115 0.219,0.167 10 false [B] 3.01,1.052 3.25,1.24 0.24,0.188 10 false [C] 3.688,1.99 3.938,2.198 0.25,0.208 10 false [D] 6.75,3.104 6.99,3.313 0.24,0.208 10 false [E] 0.281,0.604 1.229,0.802 0.948,0.198 10 false Vehicle Speed 0.854,2.052 1.229,2.25 0.375,0.198 10 false Idling 0.063,2.25 1.229,2.583 1.167,0.333 10 false Ignition Switch ON 3.438,2.656 4.198,2.979 0.76,0.323 10 false 40 seconds or more 4.396,1.052 4.635,1.24 0.24,0.188 10 false [C] 5.073,1.99 5.323,2.198 0.25,0.208 10 false [D] 5.781,1.052 6.021,1.24 0.24,0.188 10 false [C] 6.458,2 6.708,2.208 0.25,0.208 10 false [D] 4.844,2.656 5.604,2.979 0.76,0.323 10 false 40 seconds or more 6.094,2.646 6.854,2.969 0.76,0.323 10 false 40 seconds or more 2.792,0.552 3.552,0.875 0.76,0.323 10 false 35 seconds or more 4.198,0.552 4.958,0.875 0.76,0.323 10 false 35 seconds or more 5.594,0.552 6.354,0.875 0.76,0.323 10 false 35 seconds or more 1.927,2.656 2.76,2.979 0.833,0.323 10 false 120 seconds or more 0.083,1.135 1.219,1.313 1.135,0.177 10 false 40 km/h (24 mph) 0.073,1.375 1.229,1.552 1.156,0.177 10 false (900 rpm or more)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Allow the engine and idle it for 120 seconds or more [B].

8.

Drive the vehicle at 40 km/h (24 mph) or more for 35 seconds [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Idle the engine for 40 seconds or more [D].

10.

Perform step [C] and [D] at least 3 times.

11.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

12.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0133.

15.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A382692E02
0.115,0.688 0.5,0.896 0.385,0.208 10 false Case 0.635,0.688 3.125,1 2.49,0.313 10 false Heated Oxygen Sensor Output Voltage 5.948,0.604 7.01,1 1.063,0.396 10 false Main Suspected Trouble Area 0.219,2.208 0.438,2.448 0.219,0.24 10 false 1 0.583,1.333 1.625,1.615 1.042,0.281 10 false Injection Volume 3.25,2.25 4.219,2.552 0.969,0.302 10 false Output Voltage 1.365,1.604 1.76,1.813 0.396,0.208 8 false +12.5% 1.375,1.844 1.896,2.083 0.521,0.24 8 false -12.5% 3.438,2.583 4.448,2.771 1.01,0.188 8 false Higher than 0.55 V 0.948,2.865 1.854,3.031 0.906,0.167 8 false Below 0.4 V 3.25,1.333 4.292,1.615 1.042,0.281 10 false Injection Volume 0.583,2.25 1.552,2.552 0.969,0.302 10 false Output Voltage 4,1.583 4.521,1.823 0.521,0.24 8 false +12.5% 4.01,1.823 4.531,2.063 0.521,0.24 8 false -12.5% 0.823,2.615 1.969,2.854 1.146,0.24 8 false Higher than 0.55 V 3.604,2.823 4.563,3 0.958,0.177 8 false Below 0.4 V 0.219,4.25 0.438,4.49 0.219,0.24 10 false 2 0.583,3.385 1.625,3.667 1.042,0.281 10 false Injection Volume 0.583,4.417 1.552,4.719 0.969,0.302 10 false Output Voltage 3.25,3.385 4.292,3.667 1.042,0.281 10 false Injection Volume 3.25,4.417 4.219,4.719 0.969,0.302 10 false Output Voltage 0.583,5.458 1.625,5.74 1.042,0.281 10 false Injection Volume 3.25,5.448 4.292,5.729 1.042,0.281 10 false Injection Volume 3.25,7.542 4.292,7.823 1.042,0.281 10 false Injection Volume 0.573,7.542 1.615,7.823 1.042,0.281 10 false Injection Volume 0.583,6.333 1.552,6.635 0.969,0.302 10 false Output Voltage 3.24,6.333 4.208,6.635 0.969,0.302 10 false Output Voltage 3.25,8.49 4.219,8.792 0.969,0.302 10 false Output Voltage 0.583,8.5 1.552,8.802 0.969,0.302 10 false Output Voltage 1.344,3.688 1.781,3.875 0.438,0.188 8 false +12.5% 3.958,3.677 4.427,3.885 0.469,0.208 8 false +12.5% 3.958,5.729 4.365,5.885 0.406,0.156 8 false +12.5% 1.333,5.74 1.729,5.927 0.396,0.188 8 false +12.5% 1.354,7.813 1.771,7.99 0.417,0.177 8 false +12.5% 4.01,7.802 4.438,7.979 0.427,0.177 8 false +12.5% 3.979,3.885 4.365,4.083 0.385,0.198 8 false -12.5% 1.354,3.896 1.875,4.135 0.521,0.24 8 false -12.5% 1.344,5.979 1.75,6.156 0.406,0.177 8 false -12.5% 3.969,5.948 4.365,6.146 0.396,0.198 8 false -12.5% 4.021,8.031 4.448,8.24 0.427,0.208 8 false -12.5% 1.344,8.01 1.75,8.177 0.406,0.167 8 false -12.5% 0.875,4.813 1.969,5.073 1.094,0.26 8 false Almost no reaction 2.594,2.75 2.844,2.958 0.25,0.208 8 false OK 5.177,2.719 5.427,2.927 0.25,0.208 8 false OK 2.542,4.729 2.792,4.938 0.25,0.208 8 false NG 5.198,4.823 5.448,5.031 0.25,0.208 8 false OK 3.583,4.927 4.5,5.104 0.917,0.177 8 false Less than 0.4 V 3.594,4.677 4.5,4.865 0.906,0.188 8 false More than 0.5 V 0.958,6.75 1.854,6.927 0.896,0.177 8 false More than 0.5 V 0.958,6.99 1.885,7.167 0.927,0.177 8 false Less than 0.4 V 3.5,6.865 4.594,7.125 1.094,0.26 8 false Almost no reaction 5.208,6.781 5.458,6.99 0.25,0.208 8 false NG 0.896,8.938 1.99,9.198 1.094,0.26 8 false Almost no reaction 2.542,8.865 2.792,9.073 0.25,0.208 8 false NG 5.208,8.875 5.458,9.083 0.25,0.208 8 false NG 3.51,8.938 4.604,9.198 1.094,0.26 8 false Almost no reaction 0.229,6.271 0.448,6.51 0.219,0.24 10 false 3 0.25,8.458 0.469,8.698 0.219,0.24 10 false 4 5.833,3.49 6.99,3.865 1.156,0.375 10 false - Heated oxygen sensor 5.865,4.021 6.969,4.552 1.104,0.531 10 false - Heated oxygen sensor heater 5.854,4.531 6.927,5.073 1.073,0.542 10 false - Heated oxygen sensor circuit 5.813,8.083 6.813,8.271 1,0.188 10 false - Fuel pressure 5.802,8.396 7.135,9.115 1.333,0.719 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 5.865,7.479 6.781,7.854 0.917,0.375 10 false - Fuel injector assembly 5.813,5.406 6.969,5.781 1.156,0.375 10 false - No. 2 heated oxygen sensor 5.813,5.958 6.917,6.49 1.104,0.531 10 false - No. 2 heated oxygen sensor heater 5.833,6.667 7.094,7.219 1.26,0.552 10 false - No. 2 heated oxygen sensor heater circuit 3.313,0.625 5.615,0.979 2.302,0.354 10 false No. 2 Heated Oxygen Sensor Output Voltage 5.844,1.667 7,2.042 1.156,0.375 10 false - Three-way catalytic converter 5.844,2.333 7,2.708 1.156,0.375 10 false - Gas leak from exhaust system

HINT:
·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2; then press the view button.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0133)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
DTC P0133 is output A
DTC P0133 and other DTCs are output B

HINT:

If any DTCs other than P0133 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)

B

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.


e.

Warm up the heated oxygen sensor at an engine speed of 2500 rpm for approximately 90 seconds.


f.

Read the voltage output of the front heated oxygen sensor displayed on the tester, while the engine is idling.

Standard:

Fluctuates between less than 0.4 V and more than 0.5 V, and period "t" is less than 1 second (refer to table below).



A128469E05
1.542,0.431 1.779,0.601 0.237,0.170 10 1 V 1.542,1.466 1.779,1.636 0.237,0.170 10 0 V 2.522,1.382 2.634,1.527 0.112,0.144 10 t 2.752,1.382 2.864,1.527 0.112,0.144 10 t 2.586,0.23 2.823,0.400 0.237,0.170 10 OK 3.495,0.23 3.732,0.400 0.237,0.170 10 NG 4.404,0.23 4.640,0.400 0.237,0.170 10 NG 5.313,0.23 5.549,0.400 0.237,0.170 10 NG 1.429,1.149 1.778,1.319 0.349,0.170 10 0.4 V 1.429,0.745 1.891,0.915 0.462,0.170 10 0.5 V

Result
Result Proceed to
NG A
OK B


A

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

10.PERFORM CONFIRMATION DRIVING PATTERN
3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.


OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.
U158040E02
1.865,1 2.26,0.75 false 0.094,0.083 0.292,0.333 0.198,0.25 10 false *a 0.479,0.948 0.802,1.146 0.323,0.198 10 false B37 2.313,0.625 2.563,0.823 0.25,0.198 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B37-2 (+B) -Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))



OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 1))
5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (HT1A) - B84-109 (HT1A) Always Below 1 Ω
B37-3 (OX1A) - B84-112 (OX1A) Always Below 1 Ω
B37-4 (E2) - B84-90 (EX1A) Always Below 1 Ω
B37-1 (HT1A) or B84-109 (HT1A) - Body ground Always 10 kΩ or higher
B37-3 (OX1A) or B84-112 (OX1A) - Body ground Always 10 kΩ or higher
B37-4 (E2) or B84-90 (EX1A) - Body ground Always 10 kΩ or higher




OK

6.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leakage from intake system.




OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FUEL PRESSURE

OK

8.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

8.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR (SENSOR 1))
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Remove the No. 1 integration relay connector from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-2 (+B) - 1E-4 Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0133 is output A
DTC is not output B



A

B