Home › Engine / Hybrid System › 1NZ-FE LUBRICATION › OIL PUMP
RM19S0E _51 Engine / Hybrid System _051460 1NZ-FE LUBRICATION _0248140 OIL PUMP A

1NZ-FE LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 2.REMOVE FRONT WHEEL RH

Hide 51441C 3.REMOVE ENGINE UNDER COVER RH (for Plastic Type)

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH (for Plastic Type)

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Hide 27020 8.REMOVE GENERATOR ASSEMBLY

Hide 12261 11.DISCONNECT VENTILATION HOSE

A171538

a.

Disconnect the ventilation hose from the cylinder head cover.


Hide 23820 12.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

A171539

a.

Disconnect the fuel vapor feed hose assembly from the cylinder head cover.


Hide 11201 13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12305 14.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A245785

a.

Place a wooden block on a jack underneath the engine.


b.
A248250

Remove the 4 bolts, 2 nuts and the engine mounting insulator sub-assembly RH.


Hide 13407 15.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

A116203E05
2.163,1.031 2.483,1.805 false 2.418,1.823 2.597,1.986 0.179,0.163 10 *a

a.

Set the No. 1 cylinder to TDC/compression.

i.

Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


ii.
A116204E07
1.102,0.682 1.146,1.771 1.146,1.771 2.056,1.49 false 2.219,1.005 1.146,1.762 false 1.003,1.774 1.172,1.938 0.169,0.164 10 *a

Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.

Text in Illustration
*a Timing Marks

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



b.
A250432E01
0.575,1.843 0.888,1.988 0.313,0.144 10 SST 2.015,0.774 2.328,0.918 0.313,0.144 10 SST 0.638,1.567 0.749,1.822 0.749,1.822 0.788,1.3 false 2.169,1.526 2.194,0.948 2.194,0.948 2.336,1.25 false 2.68,3.087 2.833,3.231 0.153,0.144 10 *a 1.108,3.087 1.261,3.231 0.153,0.144 10 *b

Using SST, loosen the bolt while holding the crankshaft damper sub-assembly.

Text in Illustration
*a Hold
*b Loosen

SST
09213-58014  (90201-08131, 91111-50845)
09330-00021  (09330-00030)

NOTICE:

Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



c.

Remove the SSTs and the bolt.


d.

Remove the crankshaft damper sub-assembly.


Hide 11101J 17.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 16100 19.REMOVE WATER PUMP ASSEMBLY

Hide 12315A 20.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A116553

a.

Remove the 4 bolts and the transverse engine engine mounting bracket.


Hide 15100 21.REMOVE OIL PUMP ASSEMBLY (for Oil Pump Type A)

HINT:

The oil pump type A and oil pump type B listed in this section are differentiated based on the number of installation bolts for the oil pump assembly.

Oil Pump Type Number of Oil Pump Assembly Installation Bolts
A 15 bolts
B 16 bolts


a.
A306504

Remove the 15 bolts, nut and 2 wire harness clamp brackets from the oil pump assembly.


b.
A116555

Using a screwdriver with its tip wrapped in protective tape, remove the oil pump assembly by prying between the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.

NOTICE:

Do not damage the contact surfaces of the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.



c.
A116556

Remove the 2 O-rings from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 15100 22.REMOVE OIL PUMP ASSEMBLY (for Oil Pump Type B)

HINT:

The oil pump type A and oil pump type B listed in this section are differentiated based on the number of installation bolts for the oil pump assembly.

Oil Pump Type Number of Oil Pump Assembly Installation Bolts
A 15 bolts
B 16 bolts


a.
A310574

Remove the 16 bolts, nut and 2 wire harness clamp brackets from the oil pump assembly.


b.
A116555

Using a screwdriver with its tip wrapped in protective tape, remove the oil pump assembly by prying between the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.

NOTICE:

Do not damage the contact surfaces of the oil pump assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.



c.
A116556

Remove the 2 O-rings from the cylinder block sub-assembly and oil pan sub-assembly.