1.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 3 wire harness clamp brackets with 3 bolts to the manual transaxle assembly.
33403K
2.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)
Coat a new O-ring with manual transaxle gear oil and install it to the speedometer driven hole cover sub-assembly.
Install the speedometer driven hole cover sub-assembly with the bolt.
83181G
3.INSTALL SPEEDOMETER SENSOR (w/o ABS)
Coat a new O-ring with manual transaxle gear oil and install it to the speedometer sensor.
Install the speedometer driven gear to the speedometer sensor with the E-ring.
Install the speedometer sensor with the bolt.
30300
4.INSTALL MANUAL TRANSAXLE ASSEMBLY
Align the input shaft with the clutch disc and install the manual transaxle assembly to the engine assembly.
Install the 7 bolts.
Insert knock pins into the knock pin holes securely so that the end face of the manual transaxle fits close against the engine before tightening the bolts.
Be careful not to pinch wire harness, etc.
To avoid damage to the input shaft, do not forcefully shake the manual transaxle.
12325A
5.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
Remove any adhesive remaining in the 4 bolts holes on the manual transaxle assembly and 4 bolts.
Apply adhesive to 2 or 3 threads on the end of the 4 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
Following the procedures shown in the illustration, Tighten the 4 bolts in order.
| *a | Temporarily |
12372A
6.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR
Following the procedures shown in the illustration, Tighten the 5 bolts in order.
Install the transverse engine engine mounting bracket and the transverse engine engine mounting insulator with the bolt and nut.
Hold the nut and tighten the bolt.
12313
7.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET
Following the procedures shown in the illustration, tighten the 4 bolts in order.
| *a | Temporarily |
51201
8.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
43420
9.INSTALL FRONT DRIVE SHAFT ASSEMBLIES
10.CONNECT WIRE HARNESS (w/ ABS)
Connect the back up light switch connector.
Install the ground wire with the bolt.
Connect the 4 clamps and install the wire harness with the bolt.
11.CONNECT WIRE HARNESS (w/o ABS)
Connect the speedometer sensor connector.
Connect the back up light switch connector.
Install the ground wire with the bolt.
Connect the 4 clamps and install the wire harness with the bolt.
12.INSTALL CONTROL CABLE BRACKET
Install the control cable bracket with the 2 bolts.
33820B
13.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the 2 transmission control cable ends and install the 2 washers and the 2 clips.
Install 2 new clips onto the control cable bracket.
31470
14.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
Install the clutch release cylinder assembly and the clutch pipe with the 4 bolts.
28100
15.INSTALL STARTER ASSEMBLY (for 1NZ-FE)
28100
16.INSTALL STARTER ASSEMBLY (for 2NZ-FE)
74411
17.INSTALL BATTERY CARRIER
74431
18.INSTALL BATTERY TRAY
28800
19.INSTALL BATTERY
17771A
20.INSTALL AIR CLEANER BRACKET
17700
21.INSTALL AIR CLEANER ASSEMBLY
55711
22.INSTALL OUTER COWL TOP PANEL (for LHD)
55711
23.INSTALL OUTER COWL TOP PANEL (for RHD)
55722C
24.INSTALL INNER COWL TOP TO COWL BRACE (for LHD)
55722C
25.INSTALL INNER COWL TOP TO COWL BRACE (for RHD)
55815E
26.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
55815E
27.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
55735D
28.INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)
55735D
29.INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)
30.INSTALL FRONT WIPER MOTOR AND LINK
31.ADD MANUAL TRANSAXLE OIL
32.INSPECT FOR MANUAL TRANSAXLE OIL
33.INSPECT FOR MANUAL TRANSAXLE OIL LEAK