Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › from 2014.07
RM19S0E _53 Suspension _051473 REAR SUSPENSION _0248224 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  INSTALLATION  


PROCEDURE

Hide 48725G 1.INSTALL REAR AXLE CARRIER BUSH LH

a.
C107559E09
1.854,1.906 2.146,2.063 false 1.635,0.073 1.792,0.229 0.156,0.156 10 false *a 0.833,0.375 1.396,0.531 0.563,0.156 10 false 7° to 13° 2.74,1.323 2.896,1.479 0.156,0.156 10 false *c 0.542,1.323 0.698,1.479 0.156,0.156 10 false *b 2.167,1.99 2.323,2.146 0.156,0.156 10 false *d

Align the matchmarks on a new rear axle carrier bush LH and the rear axle beam assembly and provisionally install the rear axle carrier bush LH onto the rear axle beam assembly, as shown in the illustration.

Text in Illustration
*a Upper Side
*b Front Side
*c Rear Side
*d Bush Mark

NOTICE:

Install the new bush in the same orientation as the old one was prior to removal, because they are directional.



b.
C259762E02
0.271,2.208 0.438,1.958 false 1.563,1.406 2.323,1.823 2.323,1.823 2.01,1.292 false 2.323,1.865 2.74,2.083 0.417,0.219 10 false SST 0.115,2.26 0.542,2.469 0.427,0.208 10 false SST

Using SST, install the rear axle carrier bush LH onto the rear axle beam assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04030, 09955-04051, 09957-04010, 09958-04011)
09950-60020  (09951-00810)
09387-02010  
09223-15020  

NOTICE:

Do not damage the rubber portion when installing the rear axle carrier bush LH.



Hide 48725F 2.INSTALL REAR AXLE CARRIER BUSH RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 42110F 3.TEMPORARILY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.

Support the rear axle beam assembly with an engine lift.


b.

Install the rear axle beam assembly onto the vehicle and provisionally tighten the 2 bolts.


Hide 48231B 4.INSTALL REAR COIL SPRING LH

Hide 48231A 5.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 48540 6.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 7.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 42450B 8.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 42403 11.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

Hide 46430 12.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Install the No. 3 parking brake cable assembly with the bolt and a new clamp.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 46420 13.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 47324 14.INSTALL NO. 4 REAR BRAKE TUBE

a.

Install the No. 4 rear brake tube onto the rear axle beam assembly with the nut.

Torque:
5.0 N*m (51 kgf*cm, 48 in.*lbf)


b.

Connect the rear flexible hose LH to the rear axle beam assembly with a new clip.


c.

Using a union nut wrench (10 mm), install the No. 4 rear brake tube to the rear flexible hose LH while holding the rear flexible hose LH with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 47323 15.INSTALL NO. 3 REAR BRAKE TUBE

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 89516D 16.INSTALL SKID CONTROL SENSOR WIRE LH (w/ ABS)

Hide 89516C 17.INSTALL SKID CONTROL SENSOR WIRE RH (w/ ABS)

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 18.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 19. STABILIZE SUSPENSION

a.

Lower the vehicle from the jack.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 42110F 20.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY

a.
C204012E02
0.26,2.229 0.439,2.403 0.179,0.174 10 *a 2.15,2.229 2.330,2.403 0.179,0.174 10 *b

Suspend the jack on the rear axle spring seat and adjust the length of the rear shock absorber assembly to the reference value.

Text in Illustration
*a RH Side
*b LH Side

Length of shock absorber:

220 mm (8.66 in.)



b.

Fully tighten the 2 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


Hide 48540 21.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 22.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 23.BLEED BRAKE LINE

Hide 24.BLEED CLUTCH LINE (for Manual Transaxle)