Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.07–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU connector is disconnected from the brake actuator assembly.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C243295E02
2.855,0.622 3.811,0.763 0.956,0.140 10 ECU-IG NO. 2 4.789,0.329 4.965,0.469 0.175,0.140 10 34 4.831,1.387 5.007,1.527 0.175,0.140 10 1 4.718,2.513 4.993,2.662 0.275,0.149 10 A55 5.114,0.455 5.357,0.595 0.243,0.140 10 IG1 5.128,1.503 5.558,1.670 0.430,0.166 10 GND1 4.802,2.73 6.556,3.046 1.755,0.316 10 Skid Control ECU (Brake Actuator Assembly) 2.627,1.541 2.806,1.696 0.180,0.155 10 IG 2.378,2.062 2.776,2.226 0.398,0.164 10 Brake 2.271,2.582 2.588,2.731 0.317,0.148 10 CPU 1.498,3.554 1.771,3.711 0.273,0.158 10 SW 1.242,3.427 1.428,3.576 0.186,0.148 10 12 2.154,3.945 2.674,4.087 0.520,0.142 10 CAN I/F 1.505,4.528 1.701,4.676 0.195,0.148 10 F1 1.722,4.528 3.577,4.695 1.855,0.167 10 Combination Meter Assembly 0.29,4.202 0.395,4.362 0.105,0.161 10 1 0.655,4.713 0.930,4.855 0.276,0.143 10 A25 0.67,4.875 2.413,5.364 1.743,0.489 10 Brake Master Cylinder Reservoir Assembly (Brake Fluid Level Warning Switch) 0.47,4.389 0.578,4.534 0.108,0.145 10 + 0.448,5.124 0.568,5.272 0.120,0.148 10 E 0.3,5.304 0.398,5.446 0.098,0.142 10 2 4.125,5.054 4.220,5.213 0.095,0.159 10 1 2.896,5.224 3.174,5.367 0.278,0.143 10 F22 2.896,5.363 4.905,5.511 2.008,0.148 10 Parking Brake Switch Assembly 5.107,4.078 6.125,4.241 1.018,0.163 10 Main Body ECU 5.13,5.164 5.322,5.304 0.192,0.141 10 3A 5.144,4.981 5.325,5.133 0.181,0.152 10 28 5.736,4.965 5.917,5.116 0.181,0.152 10 12 4.973,5.529 6.609,5.841 1.636,0.312 10 Instrument Panel Junction Block Assembly 0.744,6.356 2.479,6.519 1.735,0.163 10 : CAN Communication Line 5.591,4.751 5.897,4.908 0.306,0.157 10 PKB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / OFF or ON OFF: Parking brake released
ON: Parking brake applied
-


f.

Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

NG

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
a.
C235854E01
0.175,0.239 0.361,0.400 0.186,0.161 10 *a

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

e.

Reconnect the brake fluid level warning switch connector.


f.

Reinstall the reservoir filler cap and strainer.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the combination meter assembly connector and the brake fluid level warning switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-12 (SW) - A25-1 (+) Always Below 1 Ω
A25-2 (E) - Body ground Always Below 1 Ω
F1-12 (SW) - Body ground Always 10 kΩ or higher



c.

Reconnect the combination meter assembly connector and the brake fluid level warning switch.



OK

9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light / OFF or ON OFF -


g.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C

h.

Connect the intelligent tester to the DLC3.



A

10.REPLACE COMBINATION METER ASSEMBLY

B

C

10.REPLACE COMBINATION METER ASSEMBLY

NEXT

11.INSPECT COMBINATION METER ASSEMBLY
11.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the intelligent tester to the DLC3.


b.

Perform Active Test of the combination meter assembly using the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The brake warning light turns ON or OFF in accordance with the intelligent tester.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END

B

C

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL).


b.

Inspect the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION).



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)
a.

Disconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 (PKB) - F22-1 Always Below 1 Ω
3A-28 (PKB) - Body ground Always 10 kΩ or higher



c.

Reconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.



OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 -12 (PKB) Always Below 1 Ω
3A-28 - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY