The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for ABS control.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).
When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.
| *1 | Speed Sensor | *2 | Speed Sensor Rotor |
| *a | Waveform (Reference):
Between Speed Sensor (-) and Body Ground |
*b | Low speed |
| *c | High speed | - | - |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1401
C1402 |
Any of the following is detected:
1.
At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more. 2.
At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more. 3.
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph)) |
·
Front speed sensor RH/LH ·
Speed sensor rotor ·
Sensor installation |
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1271
C1272 |
Detected only during Test Mode. | ·
Front speed sensor RH/LH ·
Speed sensor rotor ·
Sensor installation |
DTC C1401 and C1271 are for the front speed sensor RH.
DTC C1402 and C1272 are for the front speed sensor LH.
Turn the ignition switch off.
Check the speed sensor installation.
There is no clearance between the sensor and the front steering knuckle.
The installation bolt is tightened properly.
8.5 N*m (87 kgf*cm, 75 in.*lbf)
| *a | Normal |
| *b | Abnormal |
| *c | Clearance |
OK
NG
Remove the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor tip.
No scratches, oil, or foreign matter on the sensor tip.
If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
Reinstall the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION)
OK
NG
Remove the front axle hub sub-assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).
Check the speed sensor rotor.
No scratches, oil, or foreign matter on the rotors.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
If the front axle hub assembly needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
Reinstall the front axle hub assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION).
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
Turn the ignition switch off.
Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1401 and C1402 are not output | A |
| DTCs C1401 and/or C1402 are output | B |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).
If the front axle hub assembly needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B