Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248288 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder  


DESCRIPTION

The main body ECU receives switch signals from the door control switch, and driver side door key cylinder switch, activates the door lock motor on each door accordingly.

WIRING DIAGRAM

B284766E04
4.365,3.458 5.646,3.792 1.281,0.333 10 false Door Control Switch Assembly*3 3.833,1.542 6.333,1.948 2.5,0.406 10 false Power Window Regulator Master Switch Assembly (Door Control Switch) 0.167,6.396 1.688,6.615 1.521,0.219 10 false *3: w/o Power Window 0.167,6.094 1.969,6.313 1.802,0.219 10 false *2: w/o Rear Power Window 0.167,5.781 1.885,6 1.719,0.219 10 false *1: w/ Rear Power Window 4.438,5.292 5.51,5.677 1.073,0.385 10 false Front Door Lock Assembly LH 0.958,5.219 1.26,5.385 0.302,0.167 10 false F76 1.594,4.781 1.896,4.948 0.302,0.167 10 false UL2 1.958,4.656 2.156,4.823 0.198,0.167 10 false 12 1.958,4.26 2.156,4.427 0.198,0.167 10 false 11 1.677,4.375 1.875,4.542 0.198,0.167 10 false L2 1.594,1.104 1.896,1.271 0.302,0.167 10 false UL1 4.198,4.656 4.406,4.823 0.208,0.167 10 false 10 4.24,4.271 4.375,4.438 0.135,0.167 10 false 9 4.448,4.656 4.76,4.823 0.313,0.167 10 false UL 4.438,4.26 4.594,4.427 0.156,0.167 10 false L 4.25,2.823 4.406,2.99 0.156,0.167 10 false 2 4.25,2.427 4.385,2.594 0.135,0.167 10 false 4 4.438,2.823 4.75,2.99 0.313,0.167 10 false UL 4.448,2.417 4.604,2.583 0.156,0.167 10 false L 4.25,1 4.406,1.167 0.156,0.167 10 false 9 5.531,0.792 6.042,0.958 0.51,0.167 10 false 1*1,7*2 5.521,4.458 5.698,4.625 0.177,0.167 10 false 7 5.313,4.458 5.49,4.625 0.177,0.167 10 false E 5.531,2.635 5.708,2.802 0.177,0.167 10 false 3 3.896,0.594 4.406,0.76 0.51,0.167 10 false 2*1,3*2 1.938,1 2.135,1.167 0.198,0.167 10 false 10 1.948,0.604 2.146,0.771 0.198,0.167 10 false 9 1.698,0.729 1.896,0.896 0.198,0.167 10 false L1 4.448,1 4.76,1.167 0.313,0.167 10 false UL 4.448,0.594 4.604,0.76 0.156,0.167 10 false L 4.438,5.125 4.75,5.292 0.313,0.167 10 false H5 4.365,3.292 4.677,3.458 0.313,0.167 10 false H13 3.833,1.385 4.052,1.552 0.219,0.167 10 false H1 5.125,0.802 5.5,0.969 0.375,0.167 10 false GND 5.135,2.635 5.51,2.802 0.375,0.167 10 false GND 0.958,5.375 2,5.552 1.042,0.177 10 false Main Body ECU 3.438,1.99 3.635,2.156 0.198,0.167 10 false *3 3,1.99 3.198,2.156 0.198,0.167 10 false *3 0.146,0.115 0.896,0.323 0.75,0.208 12 false for LHD:

B289265E02
3.833,1.594 6.333,2 2.5,0.406 10 false Power Window Regulator Master Switch Assembly (Door Control Switch) 2.271,4.333 4.094,4.552 1.823,0.219 10 false *2: w/o Rear Power Window 2.271,4.021 4.042,4.24 1.771,0.219 10 false *1: w/ Rear Power Window 4.406,3.656 5.458,4.042 1.052,0.385 10 false Front Door Lock Assembly RH 0.948,3.635 1.25,3.802 0.302,0.167 10 false F76 1.604,3.125 1.906,3.292 0.302,0.167 10 false UL2 1.938,3.031 2.135,3.198 0.198,0.167 10 false 12 1.938,2.615 2.135,2.781 0.198,0.167 10 false 11 1.688,2.74 1.885,2.906 0.198,0.167 10 false L2 1.604,1.125 1.906,1.292 0.302,0.167 10 false UL1 4.26,3.021 4.469,3.188 0.208,0.167 10 false 5 4.26,2.615 4.396,2.781 0.135,0.167 10 false 6 4.448,3.031 4.76,3.198 0.313,0.167 10 false UL 4.469,2.615 4.625,2.781 0.156,0.167 10 false L 5.531,0.792 6.042,0.958 0.51,0.167 10 false 9*1,7*2 5.531,2.823 5.708,2.99 0.177,0.167 10 false 8 5.313,2.823 5.49,2.99 0.177,0.167 10 false E 3.896,1 4.406,1.167 0.51,0.167 10 false 8*1,3*2 3.896,0.604 4.406,0.771 0.51,0.167 10 false 2*1,1*2 1.948,1 2.146,1.167 0.198,0.167 10 false 10 1.958,0.615 2.156,0.781 0.198,0.167 10 false 9 1.698,0.729 1.896,0.896 0.198,0.167 10 false L1 4.448,1.01 4.76,1.177 0.313,0.167 10 false UL 4.448,0.604 4.604,0.771 0.156,0.167 10 false L 4.406,3.5 4.719,3.667 0.313,0.167 10 false G5 3.833,1.406 4.052,1.573 0.219,0.167 10 false G1 5.135,0.792 5.51,0.958 0.375,0.167 10 false GND 0.948,3.792 1.99,3.969 1.042,0.177 10 false Main Body ECU 0.146,0.094 0.823,0.354 0.677,0.26 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Proceed to the next step according to the symptom listed in the table below.

Result
Result Proceed to
Doors cannot be locked through master switch A
Doors cannot be locked through driver side door key cylinder B



A

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK SW-LOCK AND DOOR LOCK SW-UNLOCK)

B

5.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK AND UNLOCK SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK SW-LOCK AND DOOR LOCK SW-UNLOCK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door manual lock switch signal / OFF or ON OFF: Door control switch (for front driver door side) is turned to unlock position
ON: Door control switch (for front driver door side) is turned to lock position
-
Door Lock SW-Unlock Door manual unlock switch signal / OFF or ON OFF: Door control switch (for front driver door side) is turned to lock position
ON: Door control switch (for front driver door side) is turned to unlock position
-

OK:

When the switch is operating, the intelligent tester should display as shown in the table.



OK

NG

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Inspect the power window regulator master switch assembly (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

for LHD:

i.

Disconnect the F76 main body ECU connector.


ii.

Disconnect the H1*1 or H13*2 power window regulator master switch assembly (door control switch) connector.

*1: w/ Power Window

*2: w/o Power Window



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
H1-2 (L) - F76-9 (L1) Always Below 1 Ω
H1-9 (UL) - F76-10 (UL1) Always Below 1 Ω
H1-1 (GND) - Body ground Always Below 1 Ω
H1-2 (L) or F76-9 (L1) - Body ground Always 10 kΩ or higher
H1-9 (UL) or F76-10 (UL1) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
H1-3 (L) - F76-9 (L1) Always Below 1 Ω
H1-9 (UL) - F76-10 (UL1) Always Below 1 Ω
H1-7 (GND) - Body ground Always Below 1 Ω
H1-3 (L) or F76-9 (L1) - Body ground Always 10 kΩ or higher
H1-9 (UL) or F76-10 (UL1) - Body ground Always 10 kΩ or higher

w/o Power Window
Tester Connection Condition Specified Condition
H13-4 (L) - F76-9 (L1) Always Below 1 Ω
H13-2 (UL) - F76-10 (UL1) Always Below 1 Ω
H13-3 (GND) - Body ground Always Below 1 Ω
H13-4 (L) or F76-9 (L1) - Body ground Always 10 kΩ or higher
H13-2 (UL) or F76-10 (UL1) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the F76 main body ECU connector.


ii.

Disconnect the G1 power window regulator master switch assembly (door control switch) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
G1-2 (L) - F76-9 (L1) Always Below 1 Ω
G1-8 (UL) - F76-10 (UL1) Always Below 1 Ω
G1-9 (GND) - Body ground Always Below 1 Ω
G1-2 (L) or F76-9 (L1) - Body ground Always 10 kΩ or higher
G1-8 (UL) or F76-10 (UL1) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
G1-1 (L) - F76-9 (L1) Always Below 1 Ω
G1-3 (UL) - F76-10 (UL1) Always Below 1 Ω
G1-7 (GND) - Body ground Always Below 1 Ω
G1-1 (L) or F76-9 (L1) - Body ground Always 10 kΩ or higher
G1-3 (UL) - F76-10 (UL1) Always 10 kΩ or higher





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK AND UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Key SW-Lock Door lock and unlock switch signal / OFF or ON OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to lock position
-
Door Key SW-Unlock Door lock and unlock switch signal / OFF or ON OFF: Driver side door key cylinder not turned
ON: Driver side door key cylinder turned to unlock position
-

OK:

ON (driver side door key cylinder is turned to lock/unlock position) appears on the tester screen.



OK

NG

6.INSPECT FRONT DOOR LOCK ASSEMBLY (for DRIVER SIDE DOOR)
6.INSPECT FRONT DOOR LOCK ASSEMBLY (for DRIVER SIDE DOOR)
a.

Inspect the front door lock assembly (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK AND BODY GROUND)
a.

for LHD:

i.

Disconnect the F76 main body ECU.


ii.

Disconnect the H5 front door lock assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H5-9 (L) - F76-11 (L2) Always Below 1 Ω
H5-10 (UL) - F76-12 (UL2) Always Below 1 Ω
H5-7 (E) - Body ground Always Below 1 Ω
H5-9 (L) or F76-11 (L2) - Body ground Always 10 kΩ or higher
H5-10 (UL) or F76-12 (UL2) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the F76 main body ECU.


ii.

Disconnect the G5 front door lock assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-6 (L) - F76-11 (L2) Always Below 1 Ω
G5-5 (UL) - F76-12 (UL2) Always Below 1 Ω
G5-8 (E) - Body ground Always Below 1 Ω
G5-6 (L) or F76-11 (L2) - Body ground Always 10 kΩ or higher
G5-5 (UL) or F76-12 (UL2) - Body ground Always 10 kΩ or higher





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR