Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051497 SEAT BELT _0248348 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects the state of the front seat inner belt (Front Passenger Side) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the driver side and front passenger side seat belt warning light in the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM

B289089E02
5.615,3.344 6.74,4.198 1.125,0.854 10 false Combination Meter Assembly 1.667,3.167 3.656,3.865 1.99,0.698 10 false Front Seat Inner Belt Assembly (Front Passenger Side) 1.875,0.615 2.229,0.802 0.354,0.188 10 false MET 0.115,0.396 1.125,0.813 1.01,0.417 10 false from IG2 Relay 5.615,3.177 5.969,3.365 0.354,0.188 10 false F1 1.667,2.99 2.448,3.177 0.781,0.188 10 false K9*1, K8*2 0.219,5.396 0.979,5.74 0.76,0.344 10 false *2: for RHD 0.219,5.073 0.969,5.396 0.75,0.323 10 false *1: for LHD 3.073,4.188 4.813,4.521 1.74,0.333 10 false Occupant Detection Sensor 5.563,2.302 5.708,2.49 0.146,0.188 10 false 7 5.76,2.396 6.115,2.583 0.354,0.188 10 false P/SB 5.469,0.323 5.677,0.51 0.208,0.188 10 false 39 5.76,0.417 6.01,0.604 0.25,0.188 10 false IG+ 4.854,2.281 5,2.469 0.146,0.188 10 false 3 1.552,2.281 1.698,2.469 0.146,0.188 10 false 2 2.208,4.667 4.854,5.292 2.646,0.625 10 false Separate Type Front Seat Cushion Cover (Front Passenger Side) 1.792,2.604 2.688,2.938 0.896,0.333 10 false Buckle Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Perform the previous inspection procedure shown in problem symptoms table (Driver Side Seat Belt Warning Light does not Operate) before performing the following inspection procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>Driver Side Seat Belt Warning Light does not Operate).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / OFF or ON OFF: Front passenger side seat belt unfastened
ON: Front passenger side seat belt fastened
-

OK:

ON or OFF appears on the tester screen according to the front passenger side seat belt condition.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - IG CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - IG CIRCUIT)
a.
U158627E01
1.641,0.073 1.829,0.229 0.188,0.156 10 F1 2.803,1.224 3.043,1.644 false 2.924,1.673 3.213,1.829 0.289,0.156 10 IG+ 0.2,0.098 0.413,0.254 0.213,0.156 10 *a

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-39 (IG+) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

3.INSPECT SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR)
a.

Remove the separate type front seat cushion cover (occupant detection sensor) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


b.

Inspect the separate type front seat cushion cover (occupant detection sensor) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION).



OK

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION COVER (OCCUPANT DETECTION SENSOR)

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER SIDE)
a.

Remove the front seat inner belt assembly (Front Passenger Side) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Front Passenger Side)>REMOVAL).


b.

Inspect the front seat inner belt assembly (Front Passenger Side) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Front Passenger Side)>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the front seat inner belt assembly (Front Passenger Side) connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
F1-7 (P/SB) - K9-3 Always Below 1 Ω
K9-2 - Body ground Always Below 1 Ω
F1-7 (P/SB) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
F1-7 (P/SB) - K8-3 Always Below 1 Ω
K8-2 - Body ground Always Below 1 Ω
F1-7 (P/SB) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR