Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248394 BACK DOOR A

DOOR / HATCH  BACK DOOR  REASSEMBLY  


PROCEDURE

Hide 1.APPLY BODY GREASE

Hide 75442 2.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

Hide 75446A 3.INSTALL NO. 6 BACK DOOR NAME PLATE

Hide 64381A 5.INSTALL PACKAGE TRAY TRIM HANGER (w/ Package Tray Trim)

HINT:

Use the same procedures for the opposite side.


a.
B284609

Install the package tray trim hanger.


Hide 82185 6.INSTALL BACK DOOR NO. 2 WIRE

a.
B271640E02
2.313,1.813 2.74,2.083 false 3.156,0.75 2.948,1.313 false 2.375,0.677 2.125,1.146 false 1.177,1.573 1.542,1.094 false 0.438,1.396 0.833,0.969 false 0.271,1.302 0.427,1.448 0.156,0.146 10 true *2 0.979,1.49 1.135,1.635 0.156,0.146 10 true *2 3.177,0.677 3.333,0.823 0.156,0.146 10 true *2 2.396,0.594 2.552,0.74 0.156,0.146 10 true *2 2.125,1.708 2.281,1.854 0.156,0.146 10 true *1

Engage the 4 clamps and connect the connector.

Text in Illustration
*1 Hook
*2 Clamp


b.

Engage the hook and install the wire harness with the bolt.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 82186 7.INSTALL REAR WINDOW NO. 1 WIRE (w/ Rear Window Defogger)

a.
B271639E03
0.844,0.458 1.375,0.396 false 1.51,1.865 1.969,1.719 false 0.656,0.375 0.813,0.531 0.156,0.156 10 true *1 1.333,1.771 1.49,1.927 0.156,0.156 10 true *2

Engage the hook and install the bolt.

Text in Illustration
*1 Hook
*2 Clamp

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


b.

Engage the clamp and install the wire harness.


Hide 67005B 9.INSTALL BACK DOOR PANEL CUSHION

HINT:

Use the same procedures for the opposite side.


a.
B271638

Install the new back door panel cushion.


Hide 67894B 10.INSTALL BACK DOOR PANEL NO. 2 PROTECTOR

a.
B271637E01
2.363,0.674 2.516,0.831 0.152,0.158 10 *1 1.89,0.553 2.342,0.764 false

Using a piece of cloth or similar material, rub off any double-sided tape remaining on the back door panel.

Text in Illustration
*1 Double-sided Tape

NOTICE:

Installing the back door panel protector with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.



b.

Using a non-residue solvent, clean the attachment surface.


c.

Remove the double-sided tape backing of the new back door panel protector.


d.

Install the back door panel protector with 2 clips.

NOTICE:

Thoroughly press the back door panel protector to ensure that it adheres.



Hide 67893A 11.INSTALL BACK DOOR PANEL NO. 1 PROTECTOR

HINT:

Use the same procedures as for the No. 2.


Hide 85345R 12.INSTALL REAR WASHER NOZZLE (w/ Rear Wiper)

Hide 81952D 14.INSTALL REAR LIGHT COVER

a.
B271634

Engage the 6 claws and install the rear lamp cover.


Hide 84840G 15.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY (w/ Power Door Lock)

Hide 69023 16.INSTALL BACK DOOR OUTSIDE HANDLE SUB-ASSEMBLY (w/o Power Door Lock)

a.

Install the back door outside handle.


Hide 76801 17.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/ Power Door Lock)

Hide 76801 18.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/o Power Door Lock)

Hide 69790 19.INSTALL BACK DOOR LOCK CONTROL ASSEMBLY (w/o Power Door Lock)

a.

Install the back door lock control with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


b.
B284642

Engage the clamp.

NOTICE:

Make sure to pass the cable behind the wire harness.



Hide 76827A 20.INSTALL BACK DOOR GARNISH NO. 2 RETAINER (w/ Cover)

a.
B284625

Install the back door garnish No. 2 retainer with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 21.INSTALL BACK DOOR LOCK CYLINDER ASSEMBLY (w/ Power Door Lock)

a.
E228988

Engage the 2 claws and install the back door lock cylinder.


b.
E228987

Install the back door lock cylinder with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


c.

Connect the connector.


Hide 22.INSTALL BACK DOOR LOCK CYLINDER ASSEMBLY (w/o Power Door Lock)

a.

Install the back door lock cylinder with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 69772 23.INSTALL BACK DOOR LOCK CONTROL ROD (w/o Power Door Lock)

a.
B284640

Install the back door lock control rod.


Hide 74811D 24.INSTALL DOOR PULL HANDLE

a.
B271636

Engage the 4 claws and install the door pull handle.


Hide 69350 25.INSTALL BACK DOOR LOCK ASSEMBLY (w/ Power Door Lock)

Hide 69350 26.INSTALL BACK DOOR LOCK ASSEMBLY (w/o Power Door Lock)

Hide 85143R 27.INSTALL REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

Hide 85110R 28.INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

Hide 29.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

Hide 85292A 30.INSTALL REAR WIPER ARM HEAD CAP (w/ Rear Wiper)

Hide 67751 31.INSTALL BACK DOOR TRIM BOARD

a.
B271631E01
2.375,1.865 2.583,2.063 0.208,0.198 10 true (A) 0.125,0.698 0.333,0.896 0.208,0.198 10 true (A)

When reusing the back door trim board:

i.

Replace the 2 clips A with new ones.



b.

Engage the 11 clips and install the back door trim board.


Hide 76085 32.INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

Hide 76894 33.INSTALL REAR SPOILER COVER LH (w/ Rear Spoiler)

Hide 76893A 34.INSTALL REAR SPOILER COVER RH (w/ Rear Spoiler)

HINT:

Use the same procedure as for the LH side.