In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0016 | Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic). | ·
Valve timing ·
Camshaft timing oil control valve assembly ·
Camshaft timing gear assembly ·
Oil control valve filter ·
ECM |
To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016.
| Required sensors/Components (Main) | Camshaft timing gear assembly |
| Required sensors/Components (Related) | Camshaft position sensor, crankshaft position sensor |
| Frequency of Operation | Continuous |
| Engine RPM | 450 to 1000 rpm |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
Idle the engine for 5 minutes or more [C].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0016.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
Drive the vehicle for 2 to 3 minutes [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 5 minutes or more [F].
Enter the following menus: Powertrain / Engine and ECT / DTC [G].
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P0335 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0335).
The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0016 is output | A |
| P0016 and other DTCs are output | B |
If any DTCs other than P0016 are output, perform troubleshooting for those DTCs first.
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.
Connect the GTS to the DLC3.
Start the engine.
Turn the A/C on.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / VVT Change Angle #1.
Perform the Active Test. Check that the displacement angle varies.
Displacement angle varies.
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0016 is output | B |
A
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
B
Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).
OK
NG
Remove the oil control valve filter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0011).
Check that the filter is not clogged.
Filter is not clogged.
OK
NG
Replace the camshaft timing gear assembly (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear DTCs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition off and wait for at least 30 seconds.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the output pending DTCs using the GTS.
No pending DTC is output.
OK
NG