Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in ECM back-up power source circuit
(1 trip detection logic)
·

Open in back-up power source circuit

·

Battery

·

Battery terminals

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM may have been cleared.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

Stand-by RAM Initialized
ECM power source Below 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC P0560.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A254090E06
0.854,1.813 1.333,2.083 0.479,0.271 10 false Battery 0.677,1.125 1.094,1.26 0.417,0.135 10 false MAIN 1.281,0.906 1.51,1.083 0.229,0.177 10 false R/I 2.333,0.896 2.969,1.073 0.635,0.177 10 false EFI MAIN 3.135,0.896 3.833,1.083 0.698,0.188 10 false EFI No. 3 5.375,0.719 5.667,0.917 0.292,0.198 10 false A83 5.427,0.552 5.615,0.719 0.188,0.167 10 false 1 5.375,1.323 5.74,1.5 0.365,0.177 10 false B89 5.75,0.729 6.135,0.927 0.385,0.198 10 false BATT 5.75,1.333 5.958,1.479 0.208,0.146 10 false E1 5.417,1.104 5.688,1.25 0.271,0.146 10 false 16 5.917,2.24 6.292,2.385 0.375,0.146 10 false ECM 2,0.531 2.125,0.708 0.125,0.177 10 false 1 1.969,0.75 2.24,0.896 0.271,0.146 10 false 1C 3.927,0.75 4.167,0.917 0.24,0.167 10 false 1E 3.979,0.531 4.094,0.719 0.115,0.188 10 false 9 2.281,1.396 3.792,1.594 1.51,0.198 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Inspect that the battery is not depleted (See page Power Source / Network>1NZ-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

OK:

Battery is not depleted.




OK

2.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

3.INSPECT ECM (BATT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE BATTERY POSITIVE TERMINAL

3.INSPECT ECM (BATT TERMINAL VOLTAGE)
a.
U134130C05
1.302,0.938 0.917,1.75 true 0.208,0.99 0.531,1.167 0.323,0.177 10 false A83 0.76,1.802 1.24,2.01 0.479,0.208 10 false BATT 0.094,0.073 0.323,0.24 0.229,0.167 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A83-1 (BATT) - Body ground Always 11 to 14 V


Result
Result Proceed to
NG A
OK B



A

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

B

7.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Disconnect the A83 ECM connector.


b.

Remove the No. 1 integration relay from engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-9 - A83-1 (BATT) Always Below 1 Ω
1E-9 or A83-1 (BATT) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)
a.

Remove the No. 1 integration relay from engine room relay block.


b.

Disconnect the negative (-) battery terminal.


c.

Disconnect the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - Battery positive terminal Always Below 1 Ω
1C-1 or Battery positive terminal - Body ground Always 10 kΩ or higher




OK

6.INSPECT NO. 1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 INTEGRATION RELAY
a.

Inspect the No. 1 integration relay (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION).



OK

7.CHECK WHETHER DTC OUTPUT RECURS

NG

7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0560 is output A
DTC is not output B



A

B