Use the same procedure for both the RH and LH sides.
The procedure described below is for the RH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
74231
3.REMOVE FRONT ARMREST BASE UPPER PANEL
Using a moulding remover, disengage the 9 claws and 4 guides.
Disconnect the connector to remove the front armrest base upper panel.
67601
4.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the cover.
| *a | Protective Tape |
Remove the 3 screws.
Disengage the 7 clips.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly.
| *1 | Front Door Lock Remote Control Cable Assembly |
| *2 | Front Door Inside Locking Cable Assembly |
69205
5.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 4 guides to remove the front door inside handle sub-assembly.
68171B
6.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
Disengage the 7 claws to remove the front door glass inner weatherstrip as shown in the illustration.
75751C
7.REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING
Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING(for Front Side)>REMOVAL).
87910
8.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
Use the same procedure as for the LH side (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL).
68160C
9.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL).
86160
10.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67831
11.REMOVE FRONT DOOR SERVICE HOLE COVER
Remove the front door service hole cover.
Remove any tape remaining on the door side.
68101
12.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the front door service hole cover.
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch and move the front door glass so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal and the power window regulator master switch.
Remove the 2 bolts.
Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.
After the bolts are removed, do not allow the front door glass sub-assembly to fall.
69801
13.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
Disconnect the connector.
Loosen the temporary bolt.
| *a | Temporary Bolt |
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly may fall and cause damage.
Remove the 5 bolts and front door window regulator sub-assembly.
Remove the temporary bolt from the front door window regulator sub-assembly.
68141C
14.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67403F
15.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the bolt.
Disengage the guide to remove the front door rear lower frame sub-assembly.
67401F
16.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the screw.
Peel back the front door weatherstrip to remove the screw.
Remove the 2 bolts and front door front lower frame sub-assembly.
68125
17.REMOVE FRONT DOOR FIX WINDOW GLASS
Remove the front door fix window glass with front door fix window weatherstrip as shown in the illustration.
68215
18.REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP
Remove the front door fix window weatherstrip from the front door fix window glass.
69217E
19.REMOVE FRONT DOOR OUTSIDE HANDLE COVER
Remove the hole plug.
| *1 | Hole Plug |
Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover with lock cylinder.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
Disengage the 2 guides and claw to remove the front door outside handle cover.
69310
20.REMOVE FRONT DOOR LOCK ASSEMBLY
69210
21.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Remove the front door outside handle assembly as shown in the illustration.
69241H
22.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
Disengage the 3 claws to remove the front door outside handle front pad.
69242E
23.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
Disengage the 2 claws to remove the front door outside handle rear pad.
69201A
24.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the grommet and 2 claws to remove the front door outside handle frame sub-assembly as shown in the illustration.
69311A
25.REMOVE FRONT DOOR LOCK OPEN ROD
Disengage the snap to remove the front door lock open rod as indicated by the arrows in the order shown in the illustration.
| *a | Snap |
68610B
26.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
67861
27.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, remove the clip.
Using a clip remover, disengage the 29 clips to remove the front door weatherstrip.
67001A
28.REMOVE FRONT DOOR PANEL CUSHION
Remove the 2 front door panel cushions.
75921C
29.REMOVE NO. 1 BLACK OUT TAPE
Use the same procedure as for the LH side (See pageVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>REMOVAL)