Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2016.09–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  Check CAN Bus Line for Short to +B (RHD Models)  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

ECM

·

Combination meter assembly

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)

·

Main body ECU (multiplex network body ECU)

·

Power steering ECU assembly

·

Steering angle sensor (spiral cable sub-assembly)

·

Air conditioning amplifier assembly

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 1 junction connector

·

No. 2 junction connector



*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

E295566E03
0.948,5.344 2.698,5.667 1.75,0.323 10 false : CAN Branch Wire (CAN-L) 0.948,5.042 2.719,5.365 1.771,0.323 10 false : CAN Branch Wire (CAN-H) 0.948,4.76 2.615,5.083 1.667,0.323 10 false : CAN Main Wire (CAN-L) 0.948,4.438 2.615,4.76 1.667,0.323 10 false : CAN Main Wire (CAN-H) 5.427,3.781 5.865,3.948 0.438,0.167 10 false F76 5.427,3.938 7.094,4.469 1.667,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 0.115,3.802 1.677,4.323 1.563,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 1.792,3.073 2.063,3.24 0.271,0.167 10 false 14 1.802,2.521 2.073,2.688 0.271,0.167 10 false 25 2.76,3 3.031,3.167 0.271,0.167 10 false 21 2.719,3.177 2.99,3.344 0.271,0.167 10 false A61 2.76,2.448 3.031,2.615 0.271,0.167 10 false 10 1.323,3.188 1.719,3.354 0.396,0.167 10 false CANL 3.854,0.885 4.25,1.052 0.396,0.167 10 false CANL 1.323,2.615 1.74,2.781 0.417,0.167 10 false CANH 3.042,0.885 3.458,1.052 0.417,0.167 10 false CANH 2.719,2.625 2.99,2.792 0.271,0.167 10 false A61 3.792,1.375 3.979,1.542 0.188,0.167 10 false 26 3.021,1.375 3.198,1.542 0.177,0.167 10 false 13 3.677,2.063 3.865,2.229 0.188,0.167 10 false 20 3.906,2.052 4.177,2.219 0.271,0.167 10 false A61 2.948,2.063 3.052,2.229 0.104,0.167 10 false 9 3.115,2.052 3.385,2.219 0.271,0.167 10 false A61 3.688,4.208 3.875,4.375 0.188,0.167 10 false 15 3.906,4.208 4.177,4.375 0.271,0.167 10 false F82 2.969,4.208 3.073,4.375 0.104,0.167 10 false 4 3.125,4.208 3.396,4.375 0.271,0.167 10 false F82 4.5,0.573 5.073,0.74 0.573,0.167 10 false A83 4.5,0.74 5.073,0.906 0.573,0.167 10 false ECM 4.333,3.177 4.604,3.344 0.271,0.167 10 false 12 4.292,3.354 4.563,3.521 0.271,0.167 10 false F82 4.365,2.625 4.635,2.792 0.271,0.167 10 false 1 5.5,3.344 5.938,3.51 0.438,0.167 10 false CANL 5.5,2.802 5.938,2.969 0.438,0.167 10 false CANH 4.292,2.802 4.563,2.969 0.271,0.167 10 false F82 5.26,3.25 5.531,3.417 0.271,0.167 10 false 13 5.26,2.698 5.531,2.865 0.271,0.167 10 false 14 4.333,2.177 5.958,2.5 1.625,0.323 10 false No. 1 Junction Connector 0.115,3.635 0.385,3.802 0.271,0.167 10 false A54

E295567E03
0.083,7.76 2.635,8.042 2.552,0.281 10 false *2: for Manual Air Conditioning System 0.083,7.427 2.729,7.75 2.646,0.323 10 false *1: for Automatic Air Conditioning System 6.104,4.49 6.375,4.656 0.271,0.167 10 false F4 6.104,4.656 6.531,4.979 0.427,0.323 10 false DLC3 1.26,0.75 1.531,0.917 0.271,0.167 10 false F83 1.26,0.938 2.885,1.26 1.625,0.323 10 false No. 2 Junction Connector 0.052,2.167 0.323,2.333 0.271,0.167 10 false F6 0.052,6.781 2.281,7.104 2.229,0.323 10 false Air Conditioning Amplifier Assembly 0.052,2.333 2.031,2.656 1.979,0.323 10 false Power Steering ECU Assembly 5.635,1.208 6.865,1.646 1.229,0.438 10 false Navigation Receiver Assembly*4 5.49,6.281 5.76,6.448 0.271,0.167 10 false F16 5.49,6.479 7.073,6.802 1.583,0.323 10 false Airbag Sensor Assembly 5.365,8.063 7.115,8.385 1.75,0.323 10 false : CAN Branch Wire (CAN-L) 5.365,7.719 7.135,8.042 1.771,0.323 10 false : CAN Branch Wire (CAN-H) 5.365,7.396 7.031,7.719 1.667,0.323 10 false : CAN Main Wire (CAN-L) 5.365,7.052 7.031,7.375 1.667,0.323 10 false : CAN Main Wire (CAN-H) 2.615,8.344 2.885,8.51 0.271,0.167 10 false F1 2.615,8.51 4.479,8.833 1.865,0.323 10 false Combination Meter Assembly 0.063,4.229 0.5,4.396 0.438,0.167 10 false F30 0.063,4.417 1.917,4.927 1.854,0.51 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 2.135,6.052 2.406,6.219 0.271,0.167 10 false 9 2.052,6.229 2.323,6.396 0.271,0.167 10 false F41 2.094,6.427 2.365,6.594 0.271,0.167 10 false *2 2.094,5.865 2.365,6.031 0.271,0.167 10 false *2 2.146,5.521 2.417,5.688 0.271,0.167 10 false 8 2.052,5.688 2.323,5.854 0.271,0.167 10 false F41 1.771,6.052 2.042,6.219 0.271,0.167 10 false 12 1.729,6.229 2,6.396 0.271,0.167 10 false F42 1.771,6.427 2.042,6.594 0.271,0.167 10 false *1 1.771,5.865 2.042,6.031 0.271,0.167 10 false *1 1.781,5.521 2.052,5.688 0.271,0.167 10 false 11 1.729,5.688 2,5.854 0.271,0.167 10 false F42 1.385,6.24 1.667,6.406 0.281,0.167 10 false TX- 1.385,5.688 1.667,5.854 0.281,0.167 10 false TX+ 1.271,1.771 1.667,1.938 0.396,0.167 10 false CANL 1.26,1.396 1.688,1.563 0.427,0.167 10 false CANH 2.76,1.667 3.031,1.833 0.271,0.167 10 false 17 2.823,1.323 3.094,1.49 0.271,0.167 10 false 6 1.729,1.667 2,1.833 0.271,0.167 10 false 8 1.729,1.313 2,1.479 0.271,0.167 10 false 7 1.26,3.906 1.656,4.073 0.396,0.167 10 false CANL 1.26,3.563 1.688,3.729 0.427,0.167 10 false CANH 2.729,6.135 3,6.302 0.271,0.167 10 false 19 2.771,5.594 3.042,5.76 0.271,0.167 10 false 8 2.771,3.813 3.042,3.979 0.271,0.167 10 false 12 2.833,3.458 3.104,3.625 0.271,0.167 10 false 1 1.75,3.823 2.021,3.99 0.271,0.167 10 false 3 1.75,3.469 2.021,3.635 0.271,0.167 10 false 4 5.521,5.896 5.917,6.063 0.396,0.167 10 false CANL 5.521,5.521 5.948,5.688 0.427,0.167 10 false CANH 3.729,7.875 4.125,8.042 0.396,0.167 10 false CANL 3.063,7.885 3.49,8.052 0.427,0.167 10 false CANH 4.219,5.802 4.49,5.969 0.271,0.167 10 false 15 4.229,5.438 4.5,5.604 0.271,0.167 10 false 4 5.26,5.802 5.531,5.969 0.271,0.167 10 false 22 5.26,5.438 5.531,5.604 0.271,0.167 10 false 13 5.5,4.167 5.896,4.333 0.396,0.167 10 false CANL 5.5,3.802 5.927,3.969 0.427,0.167 10 false CANH 4.24,4.083 4.51,4.25 0.271,0.167 10 false 22 4.24,3.719 4.51,3.885 0.271,0.167 10 false 11 5.25,4.083 5.521,4.25 0.271,0.167 10 false 14 5.333,3.719 5.604,3.885 0.271,0.167 10 false 6 3.75,7.354 4.021,7.521 0.271,0.167 10 false 31 2.99,7.354 3.26,7.521 0.271,0.167 10 false 32 3.75,6.938 4.021,7.104 0.271,0.167 10 false 18 3.031,6.938 3.302,7.104 0.271,0.167 10 false 7 3.771,0.552 4.042,0.719 0.271,0.167 10 false 21 2.979,0.552 3.25,0.719 0.271,0.167 10 false 10 0.083,8.083 2.135,8.313 2.052,0.229 10 false *3: for Radio and Display Type 0.083,8.417 2.135,8.646 2.052,0.229 10 false *4: for Navigation Receiver Type 5.5,0.656 5.896,0.823 0.396,0.167 10 false CANL 5.5,0.281 5.927,0.448 0.427,0.167 10 false CANH 5.281,0.552 5.552,0.719 0.271,0.167 10 false 10 5.344,0.188 5.615,0.354 0.271,0.167 10 false 9 5.5,2.458 5.896,2.625 0.396,0.167 10 false CANL 5.5,2.083 5.927,2.25 0.427,0.167 10 false CANH 5.281,2.365 5.552,2.531 0.271,0.167 10 false 10 5.344,1.99 5.615,2.156 0.271,0.167 10 false 9 5.333,2.854 5.823,3.021 0.49,0.167 10 false F127 5.635,1.042 6.125,1.208 0.49,0.167 10 false F132 5.333,3.021 7.135,3.406 1.802,0.385 10 false Radio and Display Receiver Assembly*3 4.25,2.354 4.521,2.521 0.271,0.167 10 false 16 4.271,1.979 4.542,2.146 0.271,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)
a.

Turn the ignition switch off.


b.

Disconnect the F83 No. 2 junction connector.


c.
U126763C02
1.99,0.906 2.302,0.26 true 1.917,1.469 1.542,1.969 true 2.74,1.875 2.365,1.479 true 2.385,0.146 2.802,0.292 0.417,0.146 10 false CANH 1.104,1.865 1.51,2.01 0.406,0.146 10 false CANL 0.156,0.167 0.323,0.313 0.167,0.146 10 false *a 2.823,1.771 3.115,1.917 0.292,0.146 10 false BAT 1.646,0.208 1.906,0.365 0.26,0.156 10 false F4
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F4-6 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (DLC3 BRANCH WIRE)

2.CONNECT CONNECTOR
a.

Reconnect the F83 No. 2 junction connector.



NEXT

3.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR)
3.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the A61 and F82 No. 1 junction connectors.


b.
U126763C03
2,0.906 2.313,0.26 true 1.917,1.469 1.542,1.969 true 2.729,1.875 2.354,1.479 true 2.385,0.146 2.802,0.292 0.417,0.146 10 false CANH 1.115,1.865 1.583,2.063 0.469,0.198 10 false CANL 0.156,0.167 0.323,0.313 0.167,0.146 10 false *a 2.792,1.76 3.146,1.938 0.354,0.177 10 false BAT 1.646,0.208 1.906,0.365 0.26,0.156 10 false F4
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F4-6 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

4.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

NG

7.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
4.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)
a.
U158562C01
1.385,1.135 0.958,0.667 true 1.385,1.375 0.938,1.833 true 2.229,2.948 2.531,3.115 true 0.5,0.531 0.938,0.708 0.438,0.177 10 false CANH 0.5,1.771 0.885,1.948 0.385,0.177 10 false CANL 0.083,0.073 0.292,0.25 0.208,0.177 10 false *a 0.083,2.021 0.292,2.198 0.208,0.177 10 false *b 2.594,3.052 3.031,3.229 0.438,0.177 10 false BAT 0.479,1.188 0.771,1.365 0.292,0.177 10 false A61 0.531,2.719 0.823,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A61-9 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
A61-20 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

5.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

NG

16.CHECK SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)
5.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.
U158563C01
1.25,1.146 0.927,0.677 true 1.281,1.385 0.938,1.844 true 2.229,2.958 2.531,3.125 true 0.469,0.552 0.906,0.729 0.438,0.177 10 false CANH 0.542,1.792 0.927,1.969 0.385,0.177 10 false CANL 0.083,0.063 0.292,0.24 0.208,0.177 10 false *a 0.083,2.021 0.292,2.198 0.208,0.177 10 false *b 2.583,3.052 3.021,3.229 0.438,0.177 10 false BAT 0.479,1.177 0.792,1.396 0.313,0.219 10 false A61 0.521,2.719 0.813,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A61-10 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
A61-21 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

6.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

17.CHECK SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
6.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.
U158565C01
2.281,1.146 0.99,0.677 true 2.292,1.385 0.938,1.844 true 2.229,2.958 2.531,3.125 true 0.542,0.583 0.979,0.76 0.438,0.177 10 false CANH 0.531,1.781 0.917,1.958 0.385,0.177 10 false CANL 0.073,0.063 0.281,0.24 0.208,0.177 10 false *a 0.073,2 0.281,2.177 0.208,0.177 10 false *b 2.594,3.042 3.031,3.219 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.406 0.292,0.219 10 false F82 0.521,2.719 0.813,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-1 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F82-12 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

18.CHECK SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
7.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the F83 No. 2 junction connector.


b.
U158561C01
1.938,1.146 0.969,0.677 true 1.958,1.375 0.938,1.833 true 2.229,2.958 2.531,3.125 true 0.563,0.573 1,0.75 0.438,0.177 10 false CANH 0.563,1.76 0.948,1.938 0.385,0.177 10 false CANL 0.063,0.052 0.271,0.229 0.208,0.177 10 false *a 0.063,2.031 0.271,2.208 0.208,0.177 10 false *b 2.583,3.052 3.021,3.229 0.438,0.177 10 false BAT 0.49,1.188 0.792,1.417 0.302,0.229 10 false F82 0.521,2.719 0.813,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-4 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F82-15 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

8.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the A61 and F82 No. 1 junction connectors.



NEXT

9.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
9.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U158557C01
1.594,1.146 0.979,0.677 true 1.594,1.375 0.948,1.833 true 2.219,2.958 2.521,3.125 true 0.5,0.531 0.938,0.708 0.438,0.177 10 false CANH 0.521,1.781 0.906,1.958 0.385,0.177 10 false CANL 0.063,0.052 0.271,0.229 0.208,0.177 10 false *a 0.063,2.031 0.271,2.208 0.208,0.177 10 false *b 2.563,3.052 3,3.229 0.438,0.177 10 false BAT 0.479,1.188 0.833,1.375 0.354,0.188 10 false F83 0.531,2.719 0.76,2.917 0.229,0.198 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-7 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-18 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

10.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

19.CHECK SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
10.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U158558C01
1.49,1.146 0.958,0.677 true 1.5,1.375 0.938,1.833 true 2.229,2.969 2.531,3.135 true 0.5,0.531 0.938,0.708 0.438,0.177 10 false CANH 0.542,1.792 0.927,1.969 0.385,0.177 10 false CANL 0.073,0.063 0.281,0.24 0.208,0.177 10 false *a 0.073,2 0.281,2.177 0.208,0.177 10 false *b 2.594,3.063 3.031,3.24 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.365 0.292,0.177 10 false F83 0.521,2.729 0.813,2.885 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-8 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-19 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

11.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))

NG

20.CHECK SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
11.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))
a.
U158559C01
2.281,1.146 0.99,0.677 true 2.281,1.385 0.927,1.844 true 2.229,2.958 2.531,3.125 true 0.5,0.552 0.938,0.729 0.438,0.177 10 false CANH 0.51,1.771 0.896,1.948 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.594,3.052 3.031,3.229 0.438,0.177 10 false BAT 0.49,1.188 0.802,1.375 0.313,0.188 10 false F83 0.531,2.719 0.823,2.896 0.292,0.177 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-1 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-12 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

12.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

21.CHECK SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
12.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.
U158575C01
1.729,1.146 0.979,0.677 true 1.729,1.385 0.938,1.844 true 2.219,2.969 2.521,3.135 true 0.51,0.563 0.948,0.74 0.438,0.177 10 false CANH 0.521,1.781 0.906,1.958 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.583,3.073 3.021,3.25 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.344 0.292,0.156 10 false F83 0.521,2.708 0.813,2.865 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-6 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-17 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

13.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

22.CHECK SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
13.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
HINT:

For vehicles except radio and display type, go to step 14.


a.
U158743C09
0.917,0.604 1.844,1.167 true 1.833,1.385 0.927,1.938 true 2.198,2.833 2.781,2.573 true 0.333,0.948 0.625,1.104 0.292,0.156 10 false F83 0.51,2.615 0.802,2.771 0.292,0.156 10 false F4 0.458,0.5 1.021,0.656 0.563,0.156 10 false CANH 0.521,1.875 1.063,2.031 0.542,0.156 10 false CANL 0.104,0.073 0.396,0.229 0.292,0.156 10 false *a 0.104,2.177 0.396,2.333 0.292,0.156 10 false *b 2.833,2.469 3.375,2.625 0.542,0.156 10 false BAT
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-5 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-16 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

14.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NG

23.CHECK SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
14.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
HINT:

For vehicles except navigation receiver type, go to step 15.


a.
U158743C10
0.917,0.604 1.844,1.167 true 1.833,1.385 0.927,1.938 true 2.188,2.823 2.813,2.604 true 0.333,0.948 0.625,1.104 0.292,0.156 10 false F83 0.51,2.615 0.802,2.771 0.292,0.156 10 false F4 0.458,0.5 1.021,0.656 0.563,0.156 10 false CANH 0.521,1.875 1.063,2.031 0.542,0.156 10 false CANL 0.104,0.073 0.396,0.229 0.292,0.156 10 false *a 0.104,2.177 0.396,2.333 0.292,0.156 10 false *b 2.865,2.5 3.406,2.656 0.542,0.156 10 false BAT
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-5 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-16 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

15.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

NG

24.CHECK SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
15.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.
U158560C01
1.927,1.146 0.958,0.677 true 1.948,1.396 0.927,1.854 true 2.219,2.958 2.521,3.125 true 0.479,0.583 0.917,0.76 0.438,0.177 10 false CANH 0.5,1.813 0.885,1.99 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.583,3.063 3.021,3.24 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.406 0.292,0.219 10 false F83 0.531,2.719 0.781,2.896 0.25,0.177 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-4 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-15 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

25.CHECK SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
16.CHECK SHORT TO B+ IN CAN BUS WIRE (ECM MAIN WIRE)
a.

Disconnect the A83 ECM connector.


b.
U158562C02
1.396,1.146 0.969,0.677 true 1.396,1.385 0.948,1.844 true 2.219,2.958 2.521,3.125 true 0.5,0.563 0.938,0.74 0.438,0.177 10 false CANH 0.521,1.781 0.906,1.958 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.594,3.063 3.031,3.24 0.438,0.177 10 false BAT 0.479,1.177 0.771,1.333 0.292,0.156 10 false A61 0.542,2.708 0.833,2.865 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A61-9 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
A61-20 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher


Result
Result Proceed to
NG A
OK (for 1NZ-FE) B
OK (for 2NZ-FE) C



A

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM MAIN WIRE)

B

C

17.CHECK SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
a.

Disconnect the A54 skid control ECU (brake actuator assembly) connector.


b.
U158563C02
1.25,1.146 0.927,0.677 true 1.281,1.385 0.938,1.844 true 2.229,2.958 2.531,3.125 true 0.469,0.552 0.906,0.729 0.438,0.177 10 false CANH 0.542,1.792 0.927,1.969 0.385,0.177 10 false CANL 0.083,0.063 0.292,0.24 0.208,0.177 10 false *a 0.083,2.021 0.292,2.198 0.208,0.177 10 false *b 2.583,3.052 3.021,3.229 0.438,0.177 10 false BAT 0.479,1.177 0.792,1.396 0.313,0.219 10 false A61 0.521,2.719 0.813,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A61-10 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
A61-21 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)

18.CHECK SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
a.

Disconnect the F76 main body ECU (multiplex network body ECU) connector.


b.
U158565C02
2.281,1.146 0.99,0.677 true 2.292,1.385 0.938,1.844 true 2.229,2.958 2.531,3.125 true 0.542,0.583 0.979,0.76 0.438,0.177 10 false CANH 0.531,1.781 0.917,1.958 0.385,0.177 10 false CANL 0.073,0.063 0.281,0.24 0.208,0.177 10 false *a 0.073,2 0.281,2.177 0.208,0.177 10 false *b 2.594,3.042 3.031,3.219 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.406 0.292,0.219 10 false F82 0.521,2.719 0.813,2.875 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-1 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F82-12 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)

19.CHECK SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.

Disconnect the F1 combination meter assembly connector.


b.
U158557C02
1.594,1.146 0.979,0.677 true 1.594,1.375 0.948,1.833 true 2.219,2.958 2.521,3.125 true 0.5,0.531 0.938,0.708 0.438,0.177 10 false CANH 0.521,1.781 0.906,1.958 0.385,0.177 10 false CANL 0.063,0.052 0.271,0.229 0.208,0.177 10 false *a 0.063,2.031 0.271,2.208 0.208,0.177 10 false *b 2.563,3.052 3,3.229 0.438,0.177 10 false BAT 0.479,1.188 0.833,1.375 0.354,0.188 10 false F83 0.531,2.719 0.76,2.917 0.229,0.198 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-7 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-18 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY MAIN WIRE)

20.CHECK SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.

Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

*1 : for Automatic Air Conditioning System

*2 : for Manual Air Conditioning System


b.
U158558C02
1.49,1.146 0.958,0.677 true 1.5,1.375 0.938,1.833 true 2.229,2.969 2.531,3.135 true 0.5,0.531 0.938,0.708 0.438,0.177 10 false CANH 0.542,1.792 0.927,1.969 0.385,0.177 10 false CANL 0.073,0.063 0.281,0.24 0.208,0.177 10 false *a 0.073,2 0.281,2.177 0.208,0.177 10 false *b 2.594,3.063 3.031,3.24 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.365 0.292,0.177 10 false F83 0.521,2.729 0.813,2.885 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-8 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-19 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)

21.CHECK SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
a.

Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.


b.
U158559C02
2.281,1.146 0.99,0.677 true 2.281,1.385 0.927,1.844 true 2.229,2.958 2.531,3.125 true 0.5,0.552 0.938,0.729 0.438,0.177 10 false CANH 0.51,1.771 0.896,1.948 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.594,3.052 3.031,3.229 0.438,0.177 10 false BAT 0.49,1.188 0.802,1.375 0.313,0.188 10 false F83 0.531,2.719 0.823,2.896 0.292,0.177 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-1 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-12 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)

22.CHECK SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the F6 power steering ECU assembly connector.


b.
U158575C02
1.729,1.146 0.979,0.677 true 1.729,1.385 0.938,1.844 true 2.219,2.969 2.521,3.135 true 0.51,0.563 0.948,0.74 0.438,0.177 10 false CANH 0.521,1.781 0.906,1.958 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.583,3.073 3.021,3.25 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.344 0.292,0.156 10 false F83 0.521,2.708 0.813,2.865 0.292,0.156 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-6 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-17 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)

23.CHECK SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the F127 radio and display receiver assembly connector.


b.
U158743C11
0.917,0.604 1.844,1.167 true 1.833,1.385 0.927,1.938 true 2.198,2.823 2.802,2.667 true 0.333,0.948 0.625,1.104 0.292,0.156 10 false F83 0.51,2.615 0.802,2.771 0.292,0.156 10 false F4 0.458,0.5 1.021,0.656 0.563,0.156 10 false CANH 0.521,1.875 1.063,2.031 0.542,0.156 10 false CANL 0.104,0.073 0.396,0.229 0.292,0.156 10 false *a 0.104,2.177 0.396,2.333 0.292,0.156 10 false *b 2.854,2.563 3.396,2.719 0.542,0.156 10 false BAT
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-5 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-16 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

24.CHECK SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the F132 navigation receiver assembly connector.


b.
U158743C12
0.917,0.604 1.844,1.167 true 1.833,1.385 0.927,1.938 true 2.188,2.823 2.76,2.667 true 0.333,0.948 0.625,1.104 0.292,0.156 10 false F83 0.51,2.615 0.802,2.771 0.292,0.156 10 false F4 0.458,0.5 1.021,0.656 0.563,0.156 10 false CANH 0.521,1.875 1.063,2.031 0.542,0.156 10 false CANL 0.104,0.073 0.396,0.229 0.292,0.156 10 false *a 0.104,2.177 0.396,2.333 0.292,0.156 10 false *b 2.823,2.552 3.365,2.708 0.542,0.156 10 false BAT
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-5 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-16 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

25.CHECK SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.

Disconnect the F16 airbag sensor assembly connector.


b.
U158560C02
1.927,1.146 0.958,0.677 true 1.948,1.396 0.927,1.854 true 2.219,2.958 2.521,3.125 true 0.479,0.583 0.917,0.76 0.438,0.177 10 false CANH 0.5,1.813 0.885,1.99 0.385,0.177 10 false CANL 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 2.583,3.063 3.021,3.24 0.438,0.177 10 false BAT 0.49,1.188 0.781,1.406 0.292,0.219 10 false F83 0.531,2.719 0.781,2.896 0.25,0.177 10 false F4
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F83-4 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F83-15 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher




OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)