There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus lines and GND ·
ECM ·
Combination meter assembly ·
Airbag sensor assembly ·
Skid control ECU (brake actuator assembly) ·
Main body ECU (multiplex network body ECU) ·
Power steering ECU assembly ·
Steering angle sensor (spiral cable sub-assembly) ·
Air conditioning amplifier assembly ·
Radio and display receiver assembly*1 ·
Navigation receiver assembly*2 ·
No. 1 junction connector ·
No. 2 junction connector |
*1: for Radio and Display Type
*2: for Navigation Receiver Type
Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Turn the ignition switch off.
Disconnect the F83 No. 2 junction connector.
| *a | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-6 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F4-14 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Reconnect the F83 No. 2 junction connector.
NEXT
Disconnect the A61 and F82 No. 1 junction connectors.
| *a | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-6 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F4-14 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A61-9 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| A61-20 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A61-10 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| A61-21 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F82-1 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F82-12 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F83 No. 2 junction connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F82-4 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F82-15 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Reconnect the A61 and F82 No. 1 junction connectors.
NEXT
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-7 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-18 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-8 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-19 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-1 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-12 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-6 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-17 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
For vehicles except radio and display type, go to step 14.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-5 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-16 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
For vehicles except navigation receiver type, go to step 15.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-5 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-16 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-4 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-15 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the A83 ECM connector.
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A61-9 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| A61-20 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 1NZ-FE) | B |
| OK (for 2NZ-FE) | C |
A
B
C
Disconnect the A54 skid control ECU (brake actuator assembly) connector.
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A61-10 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| A61-21 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F76 main body ECU (multiplex network body ECU) connector.
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F82-1 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F82-12 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F1 combination meter assembly connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-7 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-18 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.
*1 : for Automatic Air Conditioning System
*2 : for Manual Air Conditioning System (w/ cooler)
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-8 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-19 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-1 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-12 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F6 power steering ECU assembly connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-6 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-17 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F127 radio and display receiver assembly connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-5 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-16 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F132 navigation receiver assembly connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-5 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-16 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG
Disconnect the F16 airbag sensor assembly connector.
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-4 (CANH) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
| F83-15 (CANL) - F4-4 (CG) | Ignition switch off | 200 Ω or higher |
OK
NG