DTC C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1413 Front Speed Sensor RH Output Malfunction |
DTC C1414 Front Speed Sensor LH Output Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1413 C1414 | Any of the following is detected:
|
|
| C1275 C1276 | Detected only during Test Mode. |
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | FR speed sensor open detection / Normal or Error | Normal: Normal Error: Momentary interruption | - |
| FL Speed Open | FL speed sensor open detection / Normal or Error | Normal: Normal Error: Momentary interruption | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h | When driving at constant speed: No large fluctuations |
Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1413 and C1414 are not output | A |
| DTCs C1413 and/or C1414 are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation.
| *a | Normal |
| *b | Abnormal |
| *c | Clearance |
|
| ||||
| OK | |
| 6.INSPECT FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
Reinstall the front speed sensor (Click here)
|
| ||||
| OK | |
| 7.INSPECT FRONT SPEED SENSOR ROTOR |
Remove the front speed sensor and the front axle hub sub-assembly (Click here).
Check the speed sensor rotor.
Reinstall the front speed sensor and the front axle hub sub-assembly (Click here).
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A70-7 (FR+) - A54-2 (FR+) | Always | Below 1 Ω |
| A70-6 (FR-) - A54-1 (FR-) | Always | Below 1 Ω |
| A70-19 (FL+) - A55-2 (FL+) | Always | Below 1 Ω |
| A70-18 (FL-) - A55-1 (FL-) | Always | Below 1 Ω |
| A70-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A70-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| A70-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A70-18 (FL-) - Body ground | Always | 10 kΩ or higher |
Reconnect the skid control ECU connector and the front speed sensor connector.
|
| ||||
| OK | |
| 9.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (SENSOR INPUT) |
![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A54-2 (FR+) - Body ground | Ignition switch to ON | 8 to 14 V |
| A55-2 (FL+) - Body ground | Ignition switch to ON | 8 to 14 V |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1413 and/or C1414 are output | A |
| DTCs C1413 and C1414 are not output | B |
|
| ||||
| A | |
| 11.REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTCs C1413 and C1414 are not output | A |
| DTCs C1413 and/or C1414 are output | B |
|
| ||||
| A | ||
| ||