Refer to DTCs C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1407 | Open or Short in Rear Speed Sensor RH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor RH (Rear axle hub and bearing assembly RH) ·
Skid control sensor wire RH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
| C1408 | Open or Short in Rear Speed Sensor LH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Rear speed sensor LH (Rear axle hub and bearing assembly LH) ·
Skid control sensor wire LH ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
DTC C1407 is for the rear speed sensor RH.
DTC C1408 is for the rear speed sensor LH.
Refer to DTCs C1403 and C1404.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273
Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Speed Open | RR speed sensor open detection | Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| RL Speed Open | RL speed sensor open detection | Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| Tester Display |
|---|
| RR Speed Open |
| RL Speed Open |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Wheel Speed | RR wheel speed sensor reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
0 km/h: Vehicle stopped | When driving at constant speed:
No large fluctuations |
| RL Wheel Speed | RL wheel speed sensor reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
0 km/h: Vehicle stopped | When driving at constant speed:
No large fluctuations |
| Tester Display |
|---|
| RR Wheel Speed |
| RL Wheel Speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly. If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs (C1407 and C1408) are not output | A |
| DTCs (C1407 and/or C1408) are output | B |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control sensor wire connectors.
| *a | Component without harness connected
(Skid Control Sensor Wire) |
| *b | for RH |
| *c | for LH |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P1-2 (RR+) - PF1-1 (RR+) | Always | Below 1 Ω |
| P1-1 (RR-) - PF1-2 (RR-) | Always | Below 1 Ω |
| P1-2 (RR+) - PF1-2 (RR-) | Always | 10 kΩ or higher |
| P1-2 (RR+) or PF1-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| P1-1 (RR-) - PF1-1 (RR+) | Always | 10 kΩ or higher |
| P1-1 (RR-) or PF1-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O1-2 (RL+) - OF1-1 (RL+) | Always | Below 1 Ω |
| O1-1 (RL-) - OF1-2 (RL-) | Always | Below 1 Ω |
| O1-2 (RL+) - OF1-2 (RL-) | Always | 10 kΩ or higher |
| O1-2 (RL+) or OF1-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| O1-1 (RL-) - OF1-1 (RL+) | Always | 10 kΩ or higher |
| O1-1 (RL-) or OF1-2 (RL-) - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
Reconnect the skid control sensor wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A35 skid control ECU (brake actuator assembly) connector.
Disconnect the P1*1 or O1*2 rear speed sensor connector.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-17 (RR+) - P1-2 (RR+) | Always | Below 1 Ω |
| A35-17 (RR+) or P1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| A35-16 (RR-) - P1-1 (RR-) | Always | Below 1 Ω |
| A35-16 (RR-) or P1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-5 (RL+) - O1-2 (RL+) | Always | Below 1 Ω |
| A35-5 (RL+) or O1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| A35-4 (RL-) - O1-1 (RL-) | Always | Below 1 Ω |
| A35-4 (RL-) or O1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Rear Speed Sensor) |
| *b | for RH |
| *c | for LH |
Reconnect the A35 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| P1-2 (RR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O1-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| OK (for Rear Disc Brake) | A |
| OK (for Rear Drum Brake) | B |
| NG | C |
A
B
C