The body computer receives switch signals from the power window regulator master switch assembly and driver door key cylinder lock or unlock switch signals from the front door lock assembly LH*1 or RH*2. The body computer activates the door lock motor on each door according to these signals.
*1: for LHD
*2: for RHD
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All doors cannot be locked by power window regulator master switch assembly | A |
| All doors cannot be locked by driver door key cylinder (for TMT Made) | B |
| All doors cannot be locked by driver door key cylinder (for TMMIN Made) | C |
A
B
C
Remove the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL
Inspect the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H8 power window regulator master switch assembly connector.
for RHD
Disconnect the G5 power window regulator master switch assembly connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-2 (L) - F52-19 (L1) | Always | Below 1 Ω |
| H8-9 (UL) - F52-12 (UL1) | Always | Below 1 Ω |
| H8-1 (E) - Body ground | Always | Below 1 Ω |
| H8-2 (L) or F52-19 (L1) - Body ground | Always | 10 kΩ or higher |
| H8-9 (UL) or F52-12 (UL1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G5-2 (L) - F52-19 (L1) | Always | Below 1 Ω |
| G5-8 (UL) - F52-12 (UL1) | Always | Below 1 Ω |
| G5-9 (E) - Body ground | Always | Below 1 Ω |
| G5-2 (L) or F52-19 (L1) - Body ground | Always | Below 1 Ω |
| G5-8 (UL) or F52-12 (UL1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL
Inspect the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION
for RHD
Remove the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>REMOVAL
Inspect the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMT Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H3 front door lock assembly LH connector.
for RHD
Disconnect the G2 front door lock assembly RH connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-9 (L) - F52-18 (L2) | Always | Below 1 Ω |
| H3-10 (UL) - F52-11 (UL2) | Always | Below 1 Ω |
| H3-7 (E) - Body ground | Always | Below 1 Ω |
| H3-9 (L) or F52-18 (L2) - Body ground | Always | 10 kΩ or higher |
| H3-10 (UL) or F52-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Tester Connection | Specified Condition |
|---|---|---|
| G2-6 (L) - F52-18 (L2) | Always | Below 1 Ω |
| G2-5 (UL) - F52-11 (UL2) | Always | Below 1 Ω |
| G2-8 (E) - Body ground | Always | Below 1 Ω |
| G2-6 (L) or F52-18 (L2) - Body ground | Always | 10 kΩ or higher |
| G2-5 (UL) or F52-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>REMOVAL
Inspect the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSPECTION
for RHD
Remove the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>REMOVAL
Inspect the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK(for TMMIN Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the H3 front door lock assembly LH connector.
for RHD
Disconnect the G2 front door lock assembly RH connector.
Disconnect the F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-9 (L) - F52-18 (L2) | Always | Below 1 Ω |
| H3-10 (UL) - F52-11 (UL2) | Always | Below 1 Ω |
| H3-7 (E) - Body ground | Always | Below 1 Ω |
| H3-9 (L) or F52-18 (L2) - Body ground | Always | 10 kΩ or higher |
| H3-10 (UL) or F52-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Tester Connection | Specified Condition |
|---|---|---|
| G2-6 (L) - F52-18 (L2) | Always | Below 1 Ω |
| G2-5 (UL) - F52-11 (UL2) | Always | Below 1 Ω |
| G2-8 (E) - Body ground | Always | Below 1 Ω |
| G2-6 (L) or F52-18 (L2) - Body ground | Always | 10 kΩ or higher |
| G2-5 (UL) or F52-11 (UL2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG