Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2016.10–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090850 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P*1 or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.

*1: for CVT

*2: for Manual Transaxle


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control
·

Stop Light Switch1*1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG Relay Monitor(Inside)

·

IG Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal*1

·

Neutral SW/ Clutch SW

·

Starter Request Signal


Entry&Start
·

L Code Check

·

Engine Start Request

·

Immobiliser


Starting Control
·

Ignition

·

Starter SW

·

Shift Position P or N*1


-

*1: for CVT


HINT:

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases. (for CVT)


WIRING DIAGRAM

C360235E02
0.74,0.927 1.354,1.125 0.615,0.198 10 false STAR 1.198,0.917 1.573,1.135 0.375,0.219 10 false F44 1.219,0.74 1.594,0.958 0.375,0.219 10 false 16 1.875,1.052 2.323,1.219 0.448,0.167 10 false STA 0.823,4.167 1.271,4.333 0.448,0.167 10 false STA 1.198,4.167 1.573,4.385 0.375,0.219 10 false F44 1.229,3.979 1.604,4.198 0.375,0.219 10 false 37 2.969,1.656 3.344,1.875 0.375,0.219 10 false B19 2.979,1.823 4.302,2.323 1.323,0.5 10 false Park/Neutral Position Switch*1 2.51,1.188 2.781,1.365 0.271,0.177 10 false *1 2.531,1.417 2.802,1.594 0.271,0.177 10 false 4 2.427,1.677 2.604,1.896 0.177,0.219 10 false B 2.708,1.677 2.885,1.896 0.177,0.219 10 false L 2.146,1.948 2.323,2.167 0.177,0.219 10 false P 2.146,2.24 2.323,2.458 0.177,0.219 10 false N 2.781,2.49 3.052,2.667 0.271,0.177 10 false 9 2.552,2.646 2.823,2.823 0.271,0.177 10 false *1 2.771,2.813 3.042,2.99 0.271,0.177 10 false *2 3.083,2.823 3.354,3 0.271,0.177 10 false 1 4.042,2.823 4.313,3 0.271,0.177 10 false 2 3.052,3.271 3.427,3.49 0.375,0.219 10 false A28 3.052,3.438 4.271,3.958 1.219,0.521 10 false Clutch Start Switch Assembly*2 4.438,1.74 4.708,1.917 0.271,0.177 10 false *2 4.958,0.792 5.229,0.969 0.271,0.177 10 false *1 5.729,0.792 6.104,1.01 0.375,0.219 10 false 15 5.99,0.896 6.604,1.094 0.615,0.198 10 false NSW*1 5.719,4.042 6.094,4.26 0.375,0.219 10 false 17 6,4.156 6.615,4.354 0.615,0.198 10 false STA 6.198,4.573 6.573,4.792 0.375,0.219 10 false B47 6.198,4.74 6.573,4.958 0.375,0.219 10 false ECM 0.115,4.844 1.656,5.333 1.542,0.49 10 false Certification ECU (Smart Key ECU Assembly) 2.552,5.594 2.75,5.781 0.198,0.188 10 false 5 3.313,5.573 3.51,5.76 0.198,0.188 10 false 3 2.552,6.01 2.75,6.198 0.198,0.188 10 false 2 3.313,6.01 3.51,6.198 0.198,0.188 10 false 1 2.542,6.438 3.406,6.958 0.865,0.521 10 false Starter Relay Assembly 4.438,5.396 5.052,5.594 0.615,0.198 10 false ST 4.573,5.979 4.948,6.198 0.375,0.219 10 false B15 5.552,6.333 5.927,6.552 0.375,0.219 10 false B28 4.906,5.979 5.104,6.167 0.198,0.188 10 false 1 5.615,6.156 5.813,6.344 0.198,0.188 10 false 1 4.292,6.896 5.573,7.115 1.281,0.219 10 false Starter Assembly 6.604,6.844 7.115,7.073 0.51,0.229 10 false Battery 6.448,5.698 7.063,5.896 0.615,0.198 10 false FL MAIN 0.292,6.938 1.667,7.135 1.375,0.198 10 false *1: for CVT 0.281,7.302 2.094,7.5 1.813,0.198 10 false *2: for Manual Transaxle

B406607E03
1.01,1.125 1.625,1.323 0.615,0.198 10 false STP1 1.458,1.125 1.74,1.365 0.281,0.24 10 false F43 1.49,0.938 1.771,1.177 0.281,0.24 10 false 11 0.281,1.896 1.813,2.438 1.531,0.542 10 false Certification ECU (Smart Key ECU Assembly) 3.844,1.688 4.948,2.229 1.104,0.542 10 false Stop Light Switch Assembly 5.313,1.292 5.729,1.625 0.417,0.333 10 false STOP 3.865,1.51 4.146,1.75 0.281,0.24 10 false A21 6.302,1.104 6.99,1.417 0.688,0.313 10 false for Battery 4.01,1.01 4.156,1.24 0.146,0.229 10 false L 4.677,1.021 4.823,1.25 0.146,0.229 10 false B 4.875,1.01 5.021,1.24 0.146,0.229 10 false 2 0.292,3.219 1.708,3.76 1.417,0.542 10 false Shift Lock Control Unit Assembly 0.302,3.042 0.583,3.281 0.281,0.24 10 false F20 1.354,2.729 1.573,3 0.219,0.271 10 false P2 1.635,2.625 1.854,2.896 0.219,0.271 10 false 2 3.729,2.729 4.021,2.969 0.292,0.24 10 false A35 4.042,2.729 4.333,2.969 0.292,0.24 10 false A47 4.385,2.719 4.708,2.948 0.323,0.229 10 false STP 3.813,1.021 3.958,1.281 0.146,0.26 10 false 1 3.781,2.542 3.99,2.729 0.208,0.188 10 false 28 4.094,2.552 4.302,2.74 0.208,0.188 10 false 28 0.292,4.438 1.771,4.979 1.479,0.542 10 false Rear Combination Light Assembly LH 4.24,5.719 5.719,6.26 1.479,0.542 10 false Rear Combination Light Assembly RH 0.448,5.708 1.552,6.26 1.104,0.552 10 false Center Stop Light Assembly 0.292,4.271 0.583,4.51 0.292,0.24 10 false F25 1.438,3.948 1.656,4.219 0.219,0.271 10 false B 1.646,3.865 1.865,4.135 0.219,0.271 10 false 2 4.24,5.542 4.531,5.781 0.292,0.24 10 false F26 4.438,3.063 5.417,3.531 0.979,0.469 10 false Brake Actuator Assembly 4.188,5.104 4.406,5.375 0.219,0.271 10 false 2 4.385,5.208 4.604,5.479 0.219,0.271 10 false B 0.448,5.542 0.74,5.781 0.292,0.24 10 false F30 1.635,5.104 1.854,5.375 0.219,0.271 10 false 1 0.188,6.438 1.01,6.667 0.823,0.229 10 false *1: w/o VSC 0.083,0.083 3,0.583 2.917,0.5 12 false for CVT: 4.177,4.438 5.813,4.792 1.635,0.354 10 false Brake Actuator Assembly 4.198,4.281 4.49,4.521 0.292,0.24 10 false A49 4.396,3.958 4.719,4.188 0.323,0.229 10 false STP 4.208,3.854 4.417,4.042 0.208,0.188 10 false 2 3.115,2.615 3.354,2.823 0.24,0.208 10 false *1 3.125,3.854 3.365,4.063 0.24,0.208 10 false *2 3.76,2.927 4,3.135 0.24,0.208 10 false *3 4.083,2.927 4.323,3.135 0.24,0.208 10 false *4 1.146,6.448 2.031,6.688 0.885,0.24 10 false *2: w/ VSC 2,6.438 3.635,6.677 1.635,0.24 10 false *3: except LHD with CVT 3.688,6.438 5.323,6.677 1.635,0.24 10 false *4: for LHD with CVT

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.



PROCEDURE

1.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press the lock or unlock switch of the electrical key transmitter sub-assembly and check the transmitter LED illuminates.

OK:

Transmitter LED illuminates.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

28.INSPECT TRANSMITTER BATTERY (VOLTAGE)
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

OK:

"NO" is displayed in the Data List.


Result:
Proceed to
OK
NG



OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).


OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for CVT

*2: for Manual Transaxle



Result:
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

B

C

D

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

for CVT

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever not in P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, "OFF" is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6

vi.

Turn the engine switch on (IG).


vii.

Turn the GTS on.


viii.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


ix.

According to the display on the GTS, read the Data List.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/neutral position switch status ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2


b.

for Manual Transaxle

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to help determine if the clutch start switch assembly is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6


OK:

The item in the Data List changes according to the shift position.


Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

6.CHECK FOR DTC

B

24.INSPECT PARK/NEUTRAL POSITION SWITCH

C

26.INSPECT CLUTCH START SWITCH ASSEMBLY
6.CHECK FOR DTC
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Result Proceed to
OK (for CVT) A
OK (for Manual Transaxle) B
NG C



A

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

C

GO TO DTC CHART

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status ON or OFF
for CVT

ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second has elapsed, the engine switch is released


for Manual Transaxle

ON: With the clutch pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second has elapsed, the engine switch is released


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the smart key warning light is illuminated in green on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.



Result:
Proceed to
OK
NG



OK

9.CHECK STEERING LOCK SYSTEM

NG

11.READ VALUE USING GTS (STARTER SW)
9.CHECK STEERING LOCK SYSTEM
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

10.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

NG

GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE)

10.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

*1: for CVT

*2: for Manual Transaxle


HINT:

It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

11.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P*1, press the engine switch while depressing the brake pedal*1 or clutch pedal*2 and confirm that the Data List item changes.

*1: for CVT

*2: for Manual Transaxle


Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request ON or OFF ON: Starter operation requested
OFF: Starter operation not requested
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The Data List item changes.



Result:
Proceed to
OK
NG



OK

12.INSPECT STARTER RELAY ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.INSPECT STARTER RELAY ASSEMBLY
a.

Remove the start relay assembly.


b.

Inspect the starter relay assembly.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE STARTER RELAY ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B342621C01
1.469,0.281 1.969,0.542 0.5,0.26 2.25,1.75 2.563,1.229 true 2.875,1.74 2.698,1.063 true 2.76,1.802 3.188,1.969 0.427,0.167 10 false STAR 2.104,1.802 2.563,2 0.458,0.198 10 false STA 1.594,0.333 2.052,0.531 0.458,0.198 10 false F44 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


for CVT

i.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the B47 ECM connector.


iii.

Move the shift lever to P or N.



b.
B342621C02
1.469,0.281 1.969,0.542 0.5,0.26 2.25,1.75 2.563,1.229 true 2.875,1.74 2.698,1.063 true 2.76,1.802 3.188,1.969 0.427,0.167 10 false STAR 2.104,1.802 2.563,2 0.458,0.198 10 false STA 1.594,0.333 2.052,0.531 0.458,0.198 10 false F44 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


for Manual Transaxle

i.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the B47 ECM connector.


iii.

Depressing the clutch pedal.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - Body ground 20°C (68°F) 93.75 to 136.36 Ω
F44-37 (STA) - Body ground



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

14.INSPECT STARTER ASSEMBLY

B

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

C

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
14.INSPECT STARTER ASSEMBLY
a.

Remove the starter assembly.



b.

Inspect the starter assembly.



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

15.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ENGINE ROOM RELAY BLOCK)

B

REPLACE STARTER ASSEMBLY

C

REPLACE STARTER ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ENGINE ROOM RELAY BLOCK)
a.
B359908C01
0.688,1.083 1,1.24 0.313,0.156 10 false *1 1.406,0.448 1.719,0.604 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 Starter Relay Holder


Remove the starter assembly from the vehicle to perform an inspection.



b.

Remove the starter relay assembly from the engine room relay block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B28-1 - Body ground Always 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - B15-1 Always Below 1 Ω
Relay terminal 3 or B15-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - B19-4 (B) Always Below 1 Ω
F44-16 (STAR) or B19-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY ASSEMBLY)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Remove the start relay assembly from the engine room relay block.


c.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the B47 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B19-9 (L) - Relay terminal 2 Always Below 1 Ω
B19-9 (L) or Relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STARTER RELAY ASSEMBLY)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Remove the start relay assembly from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-37 (STA) - Relay terminal 2 Always Below 1 Ω
F44-37 (STA) or Relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)
a.

Remove the start relay assembly from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - A28-2 Always Below 1 Ω
F44-16 (STAR) or A28-2 -Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY ASSEMBLY)
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Remove the start relay assembly from the engine room relay block.


c.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the B47 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-1 - Relay terminal 2 Always Below 1 Ω
A28-1 or Relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STARTER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F43 certification ECU (Smart key ECU assembly) connector.


b.

Disconnect the A21 stop light switch assembly connector.


c.

Disconnect the F20 shift lock control unit assembly connector.


d.

w/o VSC

i.

Disconnect the A35*1 or A47*2 brake actuator assembly connector.

*1: except LHD with CVT

*2: for LHD with CVT




e.

w/ VSC

i.

Disconnect the A49 brake actuator assembly connector.



f.

Disconnect the F25 rear combination light assembly LH connector.


g.

Disconnect the F26 rear combination light assembly RH connector.


h.

Disconnect the F30 center stop light assembly LH connector.


i.
B342622C03
1.5,0.25 1.917,0.5 0.417,0.25 0.615,1.302 0.375,1.792 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.583,0.271 2.042,0.469 0.458,0.198 10 false F43 0.219,1.802 0.833,2 0.615,0.198 10 false STP1
*a Front view of wire harness connector
(Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-11 (STP1) - A21-1 (L) Always Below 1 Ω
F43-11 (STP1) or A21-1 (L) - Body ground Always 10 kΩ or higher



j.

Connect the A21 stop light switch assembly connector.


k.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F43-11 (STP1) - Body ground Brake pedal released 1 V or less
Brake pedal depressed 9 V or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

24.INSPECT PARK/NEUTRAL POSITION SWITCH
a.

Remove the park/neutral position switch.



b.

Inspect the park/neutral position switch.



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

REPLACE PARK/NEUTRAL POSITION SWITCH

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - B19-4 (B) Always Below 1 Ω
F44-16 (STAR) or B19-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - A28-2 Always Below 1 Ω
F44-16 (STAR) or A28-2 -Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery

i.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


ii.
B327509C09
2.76,0.906 3.073,0.448 false 3.104,0.313 3.323,0.521 0.219,0.208 10 false *a
*a Lead Wire


Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B327510C02
2.365,1.115 1.688,0.375 false 1.49,0.281 1.802,0.479 0.313,0.198 10 false *a
*a GND


Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST



Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and trigger switch pressed 2.3 to 3.2 V




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG