Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2016.10–2017.10
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090100 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 12363A 1.TEMPORARILY INSTALL ENGINE MOVING CONTROL ROD (for Manual Transaxle)

a.

Temporarily install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

HINT:

Temporarily install the transaxle side, and then tighten the bolt to the specified torque.



Hide 12363A 2.TEMPORARILY INSTALL ENGINE MOVING CONTROL ROD (for CVT)

a.

Temporarily install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

HINT:

Temporarily install the transaxle side, and then tighten the bolt to the specified torque.



Hide 48069 3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the bolt.


Hide 48068 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48811 5.INSTALL FRONT STABILIZER BAR

Hide 48829A 6.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 7.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 8.INSTALL STEERING LINK ASSEMBLY

Hide 45025D 9.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 51201 10.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Place wooden blocks or plate lift attachments on an engine lifter, and then set the front suspension crossmember sub-assembly so that the attachments are in the positions.

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.

·

As the front suspension crossmember sub-assembly is very heavy, be sure to support it securely.




b.

Temporarily install the front suspension crossmember sub-assembly to the body with the 6 bolts.

C284274C01
4.854,3.406 5.135,3.094 false 2.323,3.417 2.063,3.198 false 0.573,3.115 0.427,3 false 6.25,2.979 6.104,2.865 false 2.375,3.427 2.583,3.573 0.208,0.146 10 true *a 0.302,3.167 0.521,3.313 0.219,0.146 10 false *b 1,3.167 1.198,3.365 0.198,0.198 10 false *c 4.708,3.375 4.927,3.521 0.219,0.146 10 true *a 5.969,3.01 6.188,3.156 0.219,0.146 10 false *b 6.677,2.99 6.875,3.188 0.198,0.198 10 false *c 6.417,1.094 6.573,1.292 0.156,0.198 10 true A 0.729,1.125 0.885,1.323 0.156,0.198 10 true A 2.01,2.771 2.167,2.969 0.156,0.198 10 true B 5.052,2.688 5.208,2.885 0.156,0.198 10 true B 1.042,3.594 1.198,3.76 0.156,0.167 10 true C 6.063,3.427 6.219,3.594 0.156,0.167 10 true C 0.615,3.052 0.938,3.24 0.323,0.188 10 false SST 6.281,2.917 6.604,3.104 0.323,0.188 10 false SST
*a Datum Hole *b Correct
*c Incorrect - -
V100136

Front of the Vehicle - -



c.

By inserting SST into the datum holes in the front suspension crossmember sub-assembly RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

SST
09670-00011  

Torque:
Bolt A : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Bolt B : 165 N*m (1683 kgf*cm, 122 ft.*lbf)
Bolt C : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole in a vertical orientation.

·

If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.




d.

Install the engine moving control rod to the engine moving control rod bracket with the bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 12363A 11.FULLY TIGHTEN ENGINE MOVING CONTROL ROD

a.

Fully tighten the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Sedan)

Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)

Hide 57533B 14.INSTALL FRONT FLOOR CENTER BRACE (for Sedan)

Hide 57533B 15.INSTALL FRONT FLOOR CENTER BRACE (for Hatchback)

Hide 48069 16.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 17.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 18.INSTALL TIE ROD END SUB-ASSEMBLY LH

Hide 45046 19.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48819A 20.INSTALL FRONT STABILIZER BOLT LH

Hide 48819A 21.INSTALL FRONT STABILIZER BOLT RH

HINT:

Use the same procedure described for the LH side.


Hide 45025D 22.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C287412E01
1.042,1.813 1.198,2.01 0.156,0.198 10 true A 2.083,0.198 2.24,0.396 0.156,0.198 10 true B

Engage clip B to the body portion and install the No. 1 steering column hole cover sub-assembly to the body portion with clip A.

NOTICE:

Make sure that the lip portion of the No. 1 steering column hole cover sub-assembly is not damaged.



Hide 45209 23.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 24.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 25.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48069 27.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 28.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 29.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51405A 30.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 31.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)