When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).
for TMMIN Made
for TMT Made
The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMMIN Made | A |
| for TMT Made | B |
A
B
Measure the voltage of the vehicle battery.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS and check for DTCs.
When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.
Door ajar warning does not operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the No. 1 indoor electrical key antenna assembly (center pillar LH):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the No. 3 indoor electrical key antenna assembly (luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the No. 3 indoor electrical key antenna assembly (luggage compartment), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| Diagnostic mode inspections fail for both channels | A |
| Diagnostic mode inspections succeed for both channels | B |
| Diagnostic mode inspection succeeds for only one of the channels | C |
A
B
C
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| Wireless and entry functions does not operate | A |
| Wireless and entry functions operate normally | B |
A
B
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.
| Result | Proceed to |
|---|---|
| Transmitter LED illuminates 3 times or more when switch is pressed and held | A |
| Transmitter LED does not illuminate when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F46 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-3 (RCO) - F46-4 (+5) | Always | Below 1 Ω |
| F44-22 (RDAS) - F46-5 (DATA) | Always | Below 1 Ω |
| F44-21 (CSEL) - F46-2 (CSEL) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| F46-1 (GND) - Body ground | Always | Below 1 Ω |
| F44-3 (RCO) or F46-4 (+5) - Body ground | Always | 10 kΩ or higher |
| F44-22 (RDAS) or F46-5 (DATA) - Body ground | Always | 10 kΩ or higher |
| F44-21 (CSEL) or F46-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Connect the F46 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F46-1 (GND) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-5 (DATA) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter subassembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F46-4 (+5) - F46-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
Below 1 V → 4.5 to 5.5 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-2 (CSEL) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery.
Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *a | Lead Wire |
Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
| *a | GND |
Measure the voltage of the transmitter battery.
When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.
Perform the measurement when the key is at room temperature.
The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Transmitter battery positive (+) - Transmitter battery negative (-) | Engine switch off, all doors closed and trigger switch pressed | 2.3 to 3.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | IG2 ON, ST ON, ALL OFF, IG1 ON or ACC ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
| Tester Display |
|---|
| Power Supply Condition |
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| F43-21 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or less |
| Proceed to |
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-10 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-33 (CUTB) - Body ground | Always | 11 to 14 V |
| F43-1 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not sound | A |
| Wireless door lock buzzer sounds | B |
A
B
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F46 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-21 (CSEL) - F46-2 (CSEL) | Always | Below 1 Ω |
| F44-21 (CSEL) or F46-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-2 (CSEL) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-5 (DATA) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door courtesy light switch assembly LH and front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly LH and front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F52 body computer connector.
Disconnect the 2N driver side junction block assembly connector.
Disconnect the F31 front door courtesy light switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2N-1 - F31-1 | Always | Below 1 Ω |
| F52-14 (PCTY) - F32-1 | Always | Below 1 Ω |
| 2N-1 or F31-1 - Body ground | Always | 10 kΩ or higher |
| F52-14 (PCTY) or F32-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-18 (DCTY) - 2N-1 | Always | Below 1 Ω |
| MB-18 (DCTY) or 2N-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door courtesy light switch assembly LH and rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly LH and rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F52 body computer connector.
Disconnect the F33 rear door courtesy light switch assembly LH connector.
Disconnect the F34 rear door courtesy light switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-14 (PCTY) - F33-1 | Always | Below 1 Ω |
| F52-14 (PCTY) - F34-1 | Always | Below 1 Ω |
| F52-14 (PCTY) or F33-1 - Body ground | Always | 10 kΩ or higher |
| F52-14 (PCTY) or F34-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage of the vehicle battery.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS and check for DTCs.
When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.
Door ajar warning does not operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
for Sedan
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna:
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (instrument panel):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
for Hatchback
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna:
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (instrument panel):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Diagnostic mode inspections fail for both channels | A |
| Diagnostic mode inspections succeed for both channels | B |
| Diagnostic mode inspection succeeds for only one of the channels | C |
A
B
C
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| Wireless and entry functions does not operate | A |
| Wireless and entry functions operate normally | B |
A
B
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal*1 or clutch pedal*2 and pressing the engine switch.
*1: for CVT
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| Transmitter LED illuminates 3 times or more when switch is pressed and held | A |
| Transmitter LED does not illuminate when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F46 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-3 (RCO) - F46-4 (+5) | Always | Below 1 Ω |
| F44-22 (RDAS) - F46-5 (DATA) | Always | Below 1 Ω |
| F44-21 (CSEL) - F46-2 (CSEL) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| F44-3 (RCO) or F46-4 (+5) - Body ground | Always | 10 kΩ or higher |
| F44-22 (RDAS) or F46-5 (DATA) - Body ground | Always | 10 kΩ or higher |
| F44-21 (CSEL) or F46-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Connect the F46 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F46-1 (GND) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-5 (DATA) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter subassembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
A
B
C
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F46-4 (+5) - F46-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
Below 1 V → 4.5 to 5.5 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-2 (CSEL) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery
Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *a | Lead Wire |
Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
| *a | GND |
Measure the voltage of the transmitter battery.
When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.
Perform the measurement when the key is at room temperature.
The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Transmitter battery positive (+) - Transmitter battery negative (-) | Engine switch off, all doors closed and trigger switch pressed | 2.3 to 3.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | All OFF, ACC ON, IG ON or ST ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| F43-21 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or less |
| Proceed to |
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 1 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 ignition relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 1 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 ignition relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Remove the No. 1 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - No. 1 ignition relay terminal 1 | Always | Below 1 Ω |
| F43-20 (IG1D) or No. 1 ignition relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the voltage according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 2 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 2 ignition relay terminal 3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| *A | for LHD | *B | for RHD |
| *1 | No. 4 Relay Block | *2 | No. 2 Ignition Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 2 ignition relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Remove the No. 2 ignition relay from No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-20 (IG1D) - No. 2 ignition relay terminal 2 | Always | Below 1 Ω |
| F43-20 (IG1D) or No. 2 ignition relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6A-1 - 6L-5 | Battery voltage not applied to terminals 6F-2 and 6J-8 | 10 kΩ or higher |
| Battery voltage applied to terminals 6F-2 and 6J-8 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Disconnect the 6F and 6J driver side block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-21 (ACCD) - 6F-2 | Always | Below 1 Ω |
| 6J-8 - Body ground | Always | Below 1 Ω |
| F43-21 (ACCD) or 6F-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-10 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-33 (CUTB) - Body ground | Always | 11 to 14 V |
| F43-1 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not sound | A |
| Wireless door lock buzzer sounds | B |
A
B
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect the F46 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-21 (CSEL) - F46-2 (CSEL) | Always | Below 1 Ω |
| F44-21 (CSEL) or F46-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Connect the F44 certification ECU (smart key ECU assembly) connector.
Connect the F46 door control receiver connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-2 (CSEL) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F46-5 (DATA) - F46-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Sedan) | B |
| NG (for Hatchback) | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check illuminated entry operation.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| OK | A |
| Abnormality when driver door opened | B |
| Abnormality when door other than driver door opened | C |
A
B
C
Remove the front door courtesy light switch assembly (for driver door).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly (for driver door).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect 6M driver side junction block assembly connector.
for LHD:
Disconnect the F31 front door courtesy light switch assembly LH connector.
for RHD:
Disconnect the F32 front door courtesy light switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-1 - 6M-2 | Always | Below 1 Ω |
| F31-1 or 6M-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F32-1 - 6M-2 | Always | Below 1 Ω |
| F32-1 or 6M-2 - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the body computer.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Disconnect the 6M driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Driver Side Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6M-2 - MB-18 (DCTY) | Always | Below 1 Ω |
| 6M-4 - MB-18 (DCTY) | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door All (Except for Driver Side Seat) | Door courtesy signal for any door other than driver door | OPEN or CLOSE | OPEN: Any door other than driver door open
CLOSE: Any door other than driver door closed |
- |
| Tester Display |
|---|
| Door All (Except for Driver Side Seat) |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| Abnormality only when front passenger door opened/closed | B |
| Abnormality only when right rear door opened/closed | C |
| Abnormality only when left rear door opened/closed | D |
A
B
C
D
Disconnect F38 combination meter assembly connector.
Disconnect F52 body computer connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-29 (ACTY) - F52-14 (PCTY) | Always | Below 1 Ω |
| F38-29 (ACTY) or F52-14 (PCTY) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the front door courtesy light switch assembly (for front passenger door).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly (for front passenger door).
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect F38 combination meter assembly connector.
for LHD:
Disconnect the F32 front door courtesy light switch assembly RH connector.
for RHD:
Disconnect the F31 front door courtesy light switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F32-1 - F38-31 (PCTY) | Always | Below 1 Ω |
| F32-1 or F38-31 (PCTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-1 - F38-31 (PCTY) | Always | Below 1 Ω |
| F31-1 or F38-31 (PCTY) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect F38 combination meter assembly connector.
Disconnect the F34 rear door courtesy light switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F34-1 - F38-33 (RRCY) | Always | Below 1 Ω |
| F34-1 or F38-33 (RRCY) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect F38 combination meter assembly connector.
Disconnect the F33 rear door courtesy light switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F33-1 - F38-32 (RLCY) | Always | Below 1 Ω |
| F33-1 or F38-32 (RLCY) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG