Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P017100  System Too Lean Bank 1  P017200  System Too Rich Bank 1  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor (sensor 1) indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.

Factors such as individual engine differences, wear over time, and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P017100 System Too Lean Bank 1 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
·

Intake system

·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

PCV valve and hose

·

PCV hose connections

·

EGR valve assembly

·

Wire harness or connector

·

ECM


Comes on DTC stored SAE Code: P0171
P017200 System Too Rich Bank 1 With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
·

Fuel injector assembly

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

EGR valve assembly

·

Wire harness or connector

·

ECM


Comes on DTC stored SAE Code: P0172

HINT:
·

When DTC P017100 is stored, the actual air fuel ratio is on the lean side. When DTC P017200 is stored, the actual air fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 may be stored. The MIL is then illuminated.



MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a malfunction of the fuel system and stores a DTC.

Example:

If the average fuel trim learned value is +41% or higher, or -44% or less, the ECM interprets this as a fuel system malfunction.

A316556E75
2.292,1.958 2.646,1.958 false 2.292,3.073 2.646,3.073 false 1.5,1.667 1.583,1.667 1.583,1.667 1.833,1.917 false 1.5,3.333 1.583,3.333 1.583,3.333 1.833,3.083 false 2.26,0.385 3.479,0.771 1.219,0.385 10 false Fuel Compensation Amount 1.917,1.865 2.531,2.063 0.615,0.198 10 false 1.41 1.917,3.01 2.323,3.229 0.406,0.219 10 false 0.56 1.979,2.438 2.594,2.635 0.615,0.198 10 false 1.0 0.125,1.146 0.896,1.344 0.771,0.198 10 false P017100 0.292,1.531 1.458,2.104 1.167,0.573 10 false +41%: Malfunction Threshold of Lean Condition 0.125,2.875 0.896,3.073 0.771,0.198 10 false P017200 0.292,3.198 1.458,3.771 1.167,0.573 10 false -44%: Malfunction Threshold of Rich Condition

MONITOR STRATEGY

Required Sensors/Components (Main) Fuel system
Required Sensors/Components (Related) Air fuel ratio sensor (sensor 1)
Mass air flow meter
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Fuel system status Closed loop
Auxiliary battery voltage 11 V or higher
Either of the following conditions is met 1 or 2
1. Engine speed Less than 1100 rpm
2. Engine load 10% or higher
Catalyst monitor Not executed

TYPICAL MALFUNCTION THRESHOLDS

P017100 and P017200: Fuel-Trim Lean/Rich
EVAP purge-cut Executing
Either of the following conditions is met 1 or 2
1. Average between short-term fuel trim and long-term fuel trim 41% or higher (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim -44% or less (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

A376920E11
2.313,2.063 2.5,0.313 2.5,0.313 2.74,0.313 true 0.531,0.052 2.521,0.25 1.99,0.198 10 false Vehicle Speed 0.302,0.344 1.406,0.865 1.104,0.521 10 false 100 km/h [Engine running] 0.396,1.229 1.417,1.698 1.021,0.469 10 false 60 km/h [Engine running] 1.083,2 1.625,2.385 0.542,0.385 10 false Idling 0.281,2.26 1.594,2.698 1.313,0.438 10 false Ignition Switch ON 1.708,2.354 1.979,2.635 0.271,0.281 10 false [A] 2.219,2.104 2.49,2.385 0.271,0.281 10 false [B] 2.969,2.104 3.24,2.385 0.271,0.281 10 false [C] 4.51,0.729 4.781,1.01 0.271,0.281 10 false [D] 5.771,2.115 6.042,2.396 0.271,0.281 10 false [E] 6.198,3.313 6.438,3.604 0.24,0.292 10 false [F] 2.833,0.229 5.698,0.521 2.865,0.292 10 false Engine coolant temperatures is 75°C or higher 1.917,3.083 2.708,3.49 0.792,0.406 10 false Warming up 2.771,3.052 3.396,3.594 0.625,0.542 10 false 5 minutes or more 6.719,2.646 7.031,2.865 0.313,0.219 10 false Time 4.073,3.042 5.198,3.469 1.125,0.427 10 false 5 minutes or more 5.531,3.021 6.156,3.49 0.625,0.469 10 false 5 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off [B].

10.

With the engine warmed up, idle the engine for 5 minutes or more [C].

11.

With the engine running, drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


12.

Stop the vehicle, and idle the engine for 5 minutes or more [E].

13.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

14.

Read the pending DTCs.

HINT:

If a pending DTC is output, the system is malfunctioning.



WIRING DIAGRAM

·

Refer to DTC P010012 for the mass air flow meter circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P010012

·

Refer to DTC P003012 for the air fuel ratio sensor (sensor 1) circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P003012


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

A low air fuel ratio sensor (sensor 1) current could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor (sensor 1) current could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P017100 AND/OR P017200)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P017100 or P017200 and other DTCs are output A
P017100 or P017200 is output B


HINT:

If any DTCs other than P017100 and/or P017200 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.CHECK PCV VALVE AND HOSE CONNECTIONS
2.CHECK PCV VALVE AND HOSE CONNECTIONS
A457192

a.

Check the PCV hose connections.



OK:

The PCV hose and PCV valve are connected correctly and are not damaged.


Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


c.

Idle the engine for 5 minutes or more with the shift lever in P.


Procedure1

d.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
Injection Volume
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 205,277,230,564

e.

Monitor the output values of the air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display (Sensor) Injection Volume Status Voltage
A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean Higher than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean Higher than 0.33 mA



Post-procedure1

f.

None.


Result:
Status A/F (O2) Sensor Current B1S1 Status A/F (O2) Sensor Current B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

EGR valve assembly


A
Rich Rich Actual air fuel ratio rich
·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

EGR valve assembly


A
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently higher than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently higher than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2].

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



A

5.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

14.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

c.

Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
Engine Independent
50004 372 25 385,205,386,428
NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR Step Position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

7.INSPECT EGR VALVE ASSEMBLY
7.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Remove the EGR valve assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL



Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



8.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.


Procedure1

c.

Read the Mass Air Flow Sensor while maintaining an engine speed of 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205
HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.



Post-procedure1

d.

None.


Result:
Result Proceed to
The value of Mass Air Flow Sensor is between 4.0 gm/sec and 18.6 gm/sec A
None of the above conditions are met B



A

9.CHECK FUEL PRESSURE

B

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
9.CHECK FUEL PRESSURE

OK

10.CHECK FOR EXHAUST GAS LEAK

NG

13.CHECK FUEL LINE
10.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION SYSTEM

NG

REPAIR OR REPLACE EXHAUST SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



11.INSPECT IGNITION SYSTEM

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.


Result:
Proceed to
OK
NG



OK

12.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE IGNITION SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



12.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.




Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



13.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

GO TO FUEL PUMP CONTROL CIRCUIT

NG

REPAIR OR REPLACE FUEL SYSTEM

14.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

NG

REPLACE AIR FUEL RATIO SENSOR

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR (SENSOR 1))

Pre-procedure1

a.

Disconnect the D40 air fuel ratio sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D40-5 (+B) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F HTR RELAY - AIR FUEL RATIO SENSOR)

16.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

Pre-procedure1

a.

Disconnect the D40 air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the D52 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-4 (HA1A) - D52-28 (HA1A) Always Below 1 Ω
D40-1 (IP+) - D52-100 (IP+) Always Below 1 Ω
D40-2 (COM) - D52-99 (COM) Always Below 1 Ω
D40-3 (VS+) - D52-98 (VS+) Always Below 1 Ω
D40-4 (HA1A) or D52-28 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
D40-1 (IP+) or D52-100 (IP+) - Body ground and other terminals Always 10 kΩ or higher
D40-2 (COM) or D52-99 (COM) - Body ground and other terminals Always 10 kΩ or higher
D40-3 (VS+) or D52-98 (VS+) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

17.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
HINT:
·

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

18.CLEAR DTC
18.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P017100 or P017200 is output B



A

END

B

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100 OR P017200)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100 OR P017200)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P017100 or P017200 is output B



A

END

B

23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

Pre-procedure1

a.

Disconnect the D23 mass air flow meter connector.


b.

Disconnect the D52 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-4 (VCC) - D52-107 (VCVG) Always Below 1 Ω
D23-3 (FG) - D52-139 (VG) Always Below 1 Ω
D23-2 (E2G) - D52-106 (E2G) Always Below 1 Ω
D23-4 (VCC) or D52-107 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-3 (FG) or D52-139 (VG) - Body ground and other terminals Always 10 kΩ or higher
D23-2 (E2G) or D52-106 (E2G) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

24.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.INSPECT MASS AIR FLOW METER

NEXT

25.CLEAR DTC
25.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P017100 or P017200 is output B



A

END

B