Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P030000  Random/Multiple Cylinder Misfire Detected  P030027  Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold  P030085  Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range  P030100  Cylinder 1 Misfire Detected  P030200  Cylinder 2 Misfire Detected  P030300  Cylinder 3 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P030000 Random/Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored SAE Code: P0300
P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold An emission deterioration misfire occurs (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on DTC stored SAE Code: -
P030085 Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored SAE Code: -
P030100 Cylinder 1 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored SAE Code: P0301
P030200 Cylinder 2 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored SAE Code: P0302
P030300 Cylinder 3 Misfire Detected Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
DTC stored SAE Code: P0303

When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

At a normal engine speed, a sufficient amount of misfires to damage the catalyst and occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor (mass air flow meter)
Mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Either of the following conditions is met (a) or (b)
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Monitor period Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Monitor period Crankshaft 200 revolutions x 3

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and Freeze Frame Data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

8.

Start the engine.

9.

Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #3, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

10.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the Freeze Frame Data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 4.5 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


11.

Check whether misfires have occurred by checking DTCs and Freeze Frame Data.

HINT:

Do not turn the ignition switch off until the output DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data are cleared.


12.

Record the DTC(s), Freeze Frame Data and misfire counts.

13.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

14.

Turn the ignition switch off and wait for at least 30 seconds.


WIRING DIAGRAM

·

Refer to DTC P010012 for the mass air flow meter circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P010012


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the ignition coil assembly, the related wire harness, or the connector) was out of order, diagnostic codes from P035113 to P035313 were output. However, these codes are not output in this vehicle.

When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #3", and "Misfire Count Cylinder #1 to #3" in the Freeze Frame Data, the pending Freeze Frame Data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.

·

Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.

-

Misfire Count Cylinder #1 to #3: Misfire count according to cylinder.

-

Catalyst OT Misfire Fuel Cut Cylinder #1 to #3: This expresses that a high-frequency misfire was concentrated in a certain cylinder and that the cylinder's fuel injection was stopped.


·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #3).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.

·

When either Short FT B1S1, Long FT B1S1 in the Freeze Frame Data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).

·

When Coolant Temperature in the Freeze Frame Data is below 75°C (167°F), the misfires have occurred only while warming up the engine.

·

Vehicle body vibrations caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P030000, P030027, P030085, P030100, P030200 or P030300 and other DTCs are output A
P030000, P030027, P030085, P030100, P030200 or P030300 is output B


HINT:

If any DTCs other than P030000, P030027, P030085, P030100, P030200 and/or P030300 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.CHECK PCV VALVE AND HOSE CONNECTIONS
2.CHECK PCV VALVE AND HOSE CONNECTIONS
A457192

a.

Check the PCV hose connections.


b.

Check the PCV valve.

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>PCV VALVE>INSPECTION

OK:

PCV hose and PCV valve are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Read and note the Misfire RPM and Misfire Load values.

Powertrain > Engine > Data List
Tester Display
Misfire RPM
Misfire Load
50003 372 146,152
HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
a.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Catalyst OT Misfire Fuel Cut
50003 372 154
Result:
Data List Result Proceed to
Catalyst OT Misfire Fuel Cut Avail A
Not Avl B




A

5.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)

B

7.READ VALUE USING GTS (MISFIRE COUNT CYLINDER #1 TO #3)
5.READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)
a.

Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Proceed to
Catalyst OT Misfire Fuel Cut History ON A
OFF B




A

6.CHECK MISFIRE COUNT

B

7.READ VALUE USING GTS (MISFIRE COUNT CYLINDER #1 TO #3)
6.CHECK MISFIRE COUNT

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


Procedure1

c.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Prohibit the Catalyst OT Misfire Prevent Fuel Cut
Data List Display
Coolant Temperature
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
50004 372 42003 205,1223,1224,1225

Post-procedure1

d.

None.


Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders have equal misfire counts B


HINT:

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.



A

8.INSPECT SPARK PLUG

B

20.CHECK INTAKE SYSTEM
7.READ VALUE USING GTS (MISFIRE COUNT CYLINDER #1 TO #3)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


Procedure1

c.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
50003 372 205,1223,1224,1225

d.

Start the engine and allow the engine to idle.


e.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS. If no misfire counts occur in any cylinders, perform procedures [A] and [B] and then check the misfire counts again.

i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].


ii.

Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #3 or DTCs displayed on the GTS [B].



Post-procedure1

f.

None.


Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders have equal misfire counts B


HINT:

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.



A

8.INSPECT SPARK PLUG

B

20.CHECK INTAKE SYSTEM
8.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK FOR SPARK (SPARK TEST)

NG

REPLACE SPARK PLUG

9.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

10.CHECK CYLINDER COMPRESSION PRESSURE
10.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (#10, #20 AND/OR #30)

NG

CHECK ENGINE TO DETERMINE CAUSE OF COMPRESSION
HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



11.CHECK TERMINAL VOLTAGE (#10, #20 AND/OR #30)

Pre-procedure1

a.

Disconnect the D52 and A53 ECM connectors.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D52-96 (#10) - A53-6 (E1) Ignition switch ON 11 to 14 V
D52-95 (#20) - A53-6 (E1) Ignition switch ON 11 to 14 V
D52-94 (#30) - A53-6 (E1) Ignition switch ON 11 to 14 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

12.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

12.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



13.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.



Result:
Proceed to
OK
NG



OK

14.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



14.CHECK FUEL PRESSURE

OK

15.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

36.CHECK FUEL LINE
15.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



16.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher with all the accessories switched off and shift position N.


c.

Read the Mass Air Flow Sensor while maintaining an engine speed of 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

Result:
Result Proceed to
The value of Mass Air Flow Sensor is between 4.0 gm/sec and 18.6 gm/sec A
None of the above conditions are met B



A

17.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

B

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
17.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

Pre-procedure1

a.

Remove the cylinder head cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



b.

Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.


Procedure1

c.
A457193C01
0.24,1.573 1.125,0.479 true 0.25,1.573 1.094,0.823 true 0.708,1.948 2.625,0.594 true 0.708,1.958 2.594,0.49 true 2.063,3.948 2.896,2.365 true 1.896,3.906 0.5,2.333 true 0.104,1.521 0.417,1.677 0.313,0.156 10 false *a 2.938,2.219 3.25,2.375 0.313,0.156 10 false *b 0.344,2.156 0.656,2.313 0.313,0.156 10 false *c 0.563,1.948 0.771,2.146 0.208,0.198 10 false *a
*a Timing Mark
*b TDC Timing Mark
*c Groove


Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration. If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

OK:

Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

18.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

18.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

c.

Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
Engine Independent
50004 372 25 385,205,386,428
NOTICE:
·

Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.

·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

19.INSPECT EGR VALVE ASSEMBLY
19.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Remove the EGR valve assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL



Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



20.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.



Result:
Proceed to
OK
NG



OK

21.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



21.CHECK FUEL PRESSURE

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

36.CHECK FUEL LINE
22.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



23.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine.


Procedure1

c.

Read the Data List.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

d.

Allow the engine to idle until Coolant Temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.


e.

Read Mass Air Flow Sensor with the engine speed at 2500 rpm.

HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.



Post-procedure1

f.

None.


Result:
Result Proceed to
The value of Mass Air Flow Sensor is between 4.0 gm/sec and 18.6 gm/sec A
None of the above conditions are met B



A

24.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

B

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
24.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

Pre-procedure1

a.

Remove the cylinder head cover sub-assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain or belt cover sub-assembly.


Procedure1

c.
A457193C01
0.24,1.573 1.125,0.479 true 0.25,1.573 1.094,0.823 true 0.708,1.948 2.625,0.594 true 0.708,1.958 2.594,0.49 true 2.063,3.948 2.896,2.365 true 1.896,3.906 0.5,2.333 true 0.104,1.521 0.417,1.677 0.313,0.156 10 false *a 2.938,2.219 3.25,2.375 0.313,0.156 10 false *b 0.344,2.156 0.656,2.313 0.313,0.156 10 false *c 0.563,1.948 0.771,2.146 0.208,0.198 10 false *a
*a Timing Mark
*b TDC Timing Mark
*c Groove


Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration. If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

OK:

Timing marks on camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

25.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

25.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

c.

Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
EGR Step Position
Engine Independent
50004 372 25 385,386,428
NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when the EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.




Post-procedure1

d.

None.


Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure increases by 10 kPa (abs) or more, compared to when the EGR valve was fully closed (0 step) OK
Other than above NG


HINT:

10 kPa = 1.45 psi



OK

27.INSPECT SPARK PLUG

NG

26.INSPECT EGR VALVE ASSEMBLY
26.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Remove the EGR valve assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL



Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

27.INSPECT SPARK PLUG

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



27.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

28.CHECK FOR SPARKS (SPARK TEST)

NG

REPLACE SPARK PLUG

28.CHECK FOR SPARKS (SPARK TEST)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

29.CHECK CYLINDER COMPRESSION PRESSURE
29.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

30.CHECK TERMINAL VOLTAGE (#10, #20 AND/OR #30)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



30.CHECK TERMINAL VOLTAGE (#10, #20 AND/OR #30)

Pre-procedure1

a.

Disconnect the D52 and A53 ECM connectors.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D52-96 (#10) - A53-6 (E1) Ignition switch ON 11 to 14 V
D52-95 (#20) - A53-6 (E1) Ignition switch ON 11 to 14 V
D52-94 (#30) - A53-6 (E1) Ignition switch ON 11 to 14 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

31.CHECK FUEL INJECTOR ASSEMBLY

NG

31.CHECK FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

Pre-procedure1

a.

Disconnect the D23 mass air flow meter connector.


b.

Disconnect the D52 ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-4 (VCC) - D52-107 (VCVG) Always Below 1 Ω
D23-3 (FG) - D52-139 (VG) Always Below 1 Ω
D23-2 (E2G) - D52-106 (E2G) Always Below 1 Ω
D23-4 (VCC) or D52-107 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-3 (FG) or D52-139 (VG) - Body ground and other terminals Always 10 kΩ or higher
D23-2 (E2G) or D52-106 (E2G) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

33.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.REPLACE MASS AIR FLOW METER
HINT:
·

If the results of the inspections performed in steps 16 and 23 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

34.CLEAR DTC
34.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

c.

Input the DTC: P030000, P030027, P030085, P030100, P030200 or P030300.


d.

Check the DTC judgment result.


Post-procedure1

e.

None.


Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200 or P030300 is output)
B



A

END

B

36.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE
HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION