Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C8149  High Voltage Power Resource Circuit Consumption Circuit Short  P1C8249  High Voltage Power Resource Circuit Over Loading  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects a short circuit malfunction or high-voltage system operation malfunction.

The cause of this malfunction may be one of the following:

Battery current sensor (IB) circuit malfunction
·

Battery current sensor (IB) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

HV battery malfunction

·

No. 1 traction battery device box assembly malfunction

·

Inverter with converter assembly malfunction

·

Air conditioner system malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

Hybrid vehicle control ECU malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



INSPECTION DESCRIPTION


A460766E02
1.115,1.792 1.938,2.01 0.823,0.219 10 false HV Battery 0.792,3.51 1.979,3.729 1.188,0.219 10 false Service Plug Grip 1.677,4.396 4.615,4.615 2.938,0.219 10 false No. 1 Traction Battery Device Box Assembly 4.604,3.813 6.938,4.042 2.333,0.229 10 false Inverter with Converter Assembly 5.052,1.323 7.156,1.542 2.104,0.219 10 false Compressor with Motor Assembly 4.958,3.219 6.031,3.427 1.073,0.208 10 false Boost Converter 6.271,3.229 6.823,3.438 0.552,0.208 10 false Inverter 2.854,2.365 3.885,2.771 1.031,0.406 10 false Battery Current Sensor 2.313,2.344 2.781,2.552 0.469,0.208 10 false SMRB 2.938,3.219 3.406,3.427 0.469,0.208 10 false SMRG 3,3.802 3.469,4.01 0.469,0.208 10 false SMRP 2.125,3.771 3.063,4.167 0.938,0.396 10 false System Main Resistor 1.115,4.75 2.458,5.01 1.344,0.26 10 false : High Voltage Line 1.104,5.063 2.448,5.323 1.344,0.26 10 false : Inspection Areas 4.531,0.656 4.75,0.875 0.219,0.219 10 false *a 4.167,1.969 4.385,2.188 0.219,0.219 10 false *b

System Diagram Location Inspection Content Reason Inspection Step
*a Check high-voltage wiring connection condition of the air conditioner compressor with motor assembly Check for short circuit 2, 4
*b Check the high voltage cables between the No. 1 traction battery device box assembly and inverter with converter assembly. Check for short circuit 3, 5


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.
Excessive overcurrent equal to a short occurs during precharge (time from when SMRP turns on until SMRG turns on).
(1 trip detection logic)
·

Air conditioning wire

·

Compressor with motor assembly

·

Inverter with converter assembly

·

No. 1 traction battery device box assembly

·

HV floor under wire


Does not come on Master Warning: Comes on
P1C8249 High Voltage Power Resource Circuit Over Loading High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.
Small battery overcurrent occurs during precharge (time from when SMRP turns on until SMRG turns on) and current continues to flow after precharge.
(1 trip detection logic)
·

Air conditioning wire

·

Compressor with motor assembly

·

Inverter with converter assembly

·

No. 1 traction battery device box assembly

·

HV floor under wire


Does not come on Master Warning: Comes on

Related Data List
DTC No. Data List
P1C8149
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting


P1C8249

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 30 seconds or more.

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.



·

If this DTC is output, do not turn the ignition switch to ON (READY) until the repair has been completed. This DTC means an excessive amperage flow through the system main resistor. The system main resistor may overheat and be damaged if the ignition switch is turned to ON (READY) repeatedly before repair.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1C8149 or P1C8249 are output and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P1C8149 or P1C8249 are output and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output B
P1C8149 or P1C8249 are output and Communication system malfunction of Hybrid control system DTCs in the table below are output C
P1C8149 or P1C8249 are output and Sensor and actuator circuit malfunction of Hybrid control system DTCs in the table below are output D
P1C8149 or P1C8249 are output and Sensor and actuator circuit malfunction of Motor generator control system DTCs in the table below are output E
P1C8149 or P1C8249 are output and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output F
P1C8149 or P1C8249 are output and System malfunction of Hybrid control system DTCs in the table below are output G
P1C8149 or P1C8249 are output and System malfunction of Motor generator control system DTCs in the table below are output H
P1C8149 or P1C8249 are output and DTCs other than the DTCs in the table below are output I
Only P1C8149 or P1C8249 is output J


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Communication system malfunction Hybrid control system U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
Motor generator control system P0A1114 DC/DC Converter Enable Circuit Short to Ground or Open
P0A1112 DC/DC Converter Enable Circuit Short to Battery
P1CCC96 DC/DC Converter Enable Component Internal Failure
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation
Motor generator control system P0D3319 DC/DC Converter Circuit Current Above Threshold

HINT:

P1C8149 or P1C8249 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

c.

Turn the ignition switch off.



A

B

C

D

E

F

G

H

I

2.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

J

2.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
2.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458489

Disconnect the air conditioning wire connector from the inverter with converter assembly.


Procedure1

c.
A380308C52
0.427,0.531 0.813,0.781 0.385,0.25 1.427,0.688 0.667,1.24 true 1.677,0.688 2.406,1.323 true 2.729,0.563 2.49,0.906 2.49,0.906 3.01,0.656 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.354,0.906 2.667,1.063 0.313,0.156 10 true *b 0.563,0.594 0.875,0.75 0.313,0.156 10 false b2 0.51,1.281 0.927,1.469 0.417,0.188 10 false ACPE 2.292,1.354 2.708,1.542 0.417,0.188 10 false ACPB
*a Air Conditioning Wire
(Inverter with Converter Assembly Side)
*b Tip of Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Condition Specified Condition
b2-2 (ACPE) (Negative (-) probe) - b2-1 (ACPB) (Positive (+) probe) Ignition switch off 100 kΩ or higher


NOTICE:
·

Do not use a megohmmeter.

·

Read the resistance after the value has stabilized.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.




Post-procedure1

d.

Reconnect the air conditioning wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR UNDER WIRE

NG

4.CHECK AIR CONDITIONING WIRE
3.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A460005

Disconnect the HV floor under wire connector from the inverter with converter assembly.


Procedure1

c.
A365608C67
0.646,0.479 1.104,0.75 0.458,0.271 1.052,1.083 1.635,0.688 false 2.667,1.104 1.979,0.688 false 0.083,0.042 0.396,0.198 0.313,0.156 10 false *a 0.771,0.99 1.083,1.146 0.313,0.156 10 false CBI 2.74,1.031 3.052,1.188 0.313,0.156 10 false CEI 0.802,0.542 1.115,0.698 0.313,0.156 10 false a3
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a3-1 (CBI) - a3-2 (CEI) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure not to damage or deform the terminal being inspected.



Post-procedure1

d.

Reconnect the HV floor under wire connector.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

5.CHECK FLOOR UNDER WIRE
4.CHECK AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458489

Disconnect the air conditioning wire connector from the inverter with converter assembly.


c.
A458496N01
1.229,0.563 1.594,0.823 0.365,0.26 1.344,0.615 1.552,0.792 0.208,0.177 10 true b1

Disconnect the b1 air conditioning wire from the compressor with motor assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for M15A-FXE)>REMOVAL



Procedure1

d.
A380308C52
0.427,0.531 0.813,0.781 0.385,0.25 1.427,0.688 0.667,1.24 true 1.677,0.688 2.406,1.323 true 2.729,0.563 2.49,0.906 2.49,0.906 3.01,0.656 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.354,0.906 2.667,1.063 0.313,0.156 10 true *b 0.563,0.594 0.875,0.75 0.313,0.156 10 false b2 0.51,1.281 0.927,1.469 0.417,0.188 10 false ACPE 2.292,1.354 2.708,1.542 0.417,0.188 10 false ACPB
*a Air Conditioning Wire
(Inverter with Converter Assembly Side)
*b Tip of Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b2-2 (ACPE) - b2-1 (ACPB) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Post-procedure1

e.

Reconnect the air conditioning wire connector to the inverter with converter assembly.


f.

Reconnect the b1 air conditioning wire to the compressor with motor assembly.


Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING WIRE

5.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON(READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N02
2.094,1.448 2.417,1.708 0.323,0.26 1.719,1.74 2.042,2 0.323,0.26 1.813,1.792 1.99,1.958 0.177,0.167 10 true a1 2.177,1.5 2.365,1.677 0.188,0.177 10 true a2

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.


d.
A460005

Disconnect the HV floor under wire connector from the inverter with converter assembly.


Procedure1

e.
A365608C67
0.646,0.479 1.104,0.75 0.458,0.271 1.052,1.083 1.635,0.688 false 2.667,1.104 1.979,0.688 false 0.083,0.042 0.396,0.198 0.313,0.156 10 false *a 0.771,0.99 1.083,1.146 0.313,0.156 10 false CBI 2.74,1.031 3.052,1.188 0.313,0.156 10 false CEI 0.802,0.542 1.115,0.698 0.313,0.156 10 false a3
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a3-1 (CBI) - a3-2 (CEI) Ignition switch off 10 kΩ or higher


NOTICE:

Be sure not to damage or deform the terminal being inspected.



Post-procedure1

f.

Reconnect the HV floor under wire connector to the inverter with converter assembly.


g.

Reconnect the HV floor under wire connectors to the No. 1 traction battery device box assembly.


h.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG