Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P001100  Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1  


DESCRIPTION

Refer to DTC P001011.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P001011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P001100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Deviation in actual camshaft angle and target camshaft angle (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

Camshaft timing sprocket assembly

·

Oil control valve filter

·

Camshaft timing oil control valve assembly (for intake camshaft) circuit

·

ECM


Comes on DTC stored Engine B

HINT:

This DTC is stored when all of the following conditions are met:

1.

The difference between the target VVT angle and actual VVT angle is more than 10° for 7.7 seconds or more.

2.

After condition 1 is met, the camshaft timing oil control valve assembly (for intake camshaft) is forcibly activated to clean the oil paths.

3.

Condition 1 is met 3 times after the camshaft timing oil control valve assembly (for intake camshaft) is forcibly activated.



WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


·

DTC P001100 (system performance) will be stored if the vehicle is driven in an urban area (when acceleration, constant speed driving at high engine speeds and deceleration are repeated at intervals of 7.7 seconds or more).

·

DTC P001100 (timing over-advanced) will be stored if the engine is allowed to idle for 15 seconds after it is warmed up. If the DTC is not stored, race the engine and allow it to idle for another 15 seconds.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

DTC P001100 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P001100)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If any DTCs other than P001100 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
Only P001100 is output A
P001100 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Check the engine speed when operating the camshaft timing oil control valve assembly (for intake camshaft) using the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Intake VVT OCV Control Duty Ratio Bank 1
50004 372 4 397,296

Result:
Result Proceed to
Engine changes from steady idling to rough idling or engine stalling A
No change in engine speed B


Post-procedure1

d.

None.



A

3.CHECK VALVE TIMING

B

6.CHECK ECM OUTPUT SIGNAL (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) SIGNAL)
3.CHECK VALVE TIMING
a.

Check for looseness or a jumped tooth in the timing chain.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


OK:

The match marks of the crankshaft pulley and camshaft pulley align.



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

11.CHECK ENGINE MECHANICAL SYSTEM
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle for 20 minutes or more.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001100 is output A
DTCs are not output B


HINT:

DTC P001100 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.



Post-procedure1

d.

None.



A

6.CHECK ECM OUTPUT SIGNAL (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) SIGNAL)

B

END

6.CHECK ECM OUTPUT SIGNAL (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) SIGNAL)
A120345C07
0.417,0.917 0.854,1.229 0.438,0.313 0.125,0.094 0.385,0.396 0.26,0.302 10 false *a 0.135,2.188 0.292,2.344 0.156,0.156 10 false *b 2.615,3.583 3.021,3.875 0.406,0.292 10 false GND 0.51,0.99 0.844,1.354 0.333,0.365 10 false D77
*a Front view of wire harness connector
(Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft))
*b Camshaft Timing Oil Control Valve (for Intake Camshaft) Signal Waveform


Pre-procedure1

a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


Procedure1

b.

While running the engine at idle, check the waveform between the terminals of the camshaft timing oil control valve assembly (for intake camshaft) connector using the oscilloscope.

Item Condition
Tester Connection D77-1 - D77-2
Tool Setting 5 V/DIV., 1 ms./DIV.
Condition Idling

OK:

Correct waveform is as shown



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

7.INSPECT OIL CONTROL VALVE FILTER

NG

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)
7.INSPECT OIL CONTROL VALVE FILTER
A322749

Pre-procedure1

a.

Remove the oil control valve filter.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



Post-procedure1

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG


Procedure1

c.

None.



OK

8.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

8.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

9.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

9.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION

OK:

The camshaft timing sprocket assembly rotates smoothly when applying pressure.


Result:
Proceed to
OK
NG



OK

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100)

NG

REPLACE CAMSHAFT TIMING SPROCKET ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D77-2 (+) - D50-75 (OCV+) Always Below 1 Ω
D77-1 (-) - D50-74 (OCV-) Always Below 1 Ω
D77-2 (+) or D50-75 (OCV+) - Body ground Always 10 kΩ or higher
D77-1 (-) or D50-74 (OCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

12.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

12.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P001100)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle for 20 minutes.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
P001100 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B