16268L
1.REMOVE WATER BY-PASS PIPE
Remove the 3 bolts and water by-pass pipe from the cylinder head sub-assembly and timing chain cover sub-assembly.
Remove the 2 water by-pass pipe gaskets from the water by-pass pipe.
15301
2.REMOVE ENGINE OIL LEVEL DIPSTICK
Remove the engine oil level dipstick.
11409
3.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly and the oil pan sub-assembly.
Remove the O-ring from the engine oil level dipstick guide.
19100P
4.REMOVE SPARK PLUG
11101E
5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)
11101E
6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)
89422A
7.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11101J
8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)
11101J
9.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)
11301K
10.REMOVE CRANKSHAFT POSITION SENSOR
89615
11.REMOVE KNOCK CONTROL SENSOR
83530
12.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
15678A
13.REMOVE OIL CONTROL VALVE FILTER
| *a | 8 mm Hexagon Socket Wrench |
Using an 8 mm hexagon socket wrench, remove the head straight screw plug.
| *1 | Oil Control Valve Filter |
| *2 | Gasket |
| *3 | Head Straight Screw Plug |
Remove the oil control valve filter and gasket.
12108
14.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.
Remove the oil filler cap gasket from the oil filler cap sub-assembly.
11201
15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 17 bolts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
Remove the camshaft bearing cap oil hole gasket.
11213
16.REMOVE CYLINDER HEAD COVER GASKET
Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.
12261
17.REMOVE VENTILATION HOSE
12204
18.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
12204A
19.REMOVE VENTILATION SYSTEM GROMMET
20.REMOVE GROMMET
Remove the grommet from the cylinder head cover sub-assembly.
12101A
21.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug.
Remove the oil pan drain plug gasket.
12101
22.REMOVE OIL PAN SUB-ASSEMBLY
12121
23.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 3 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.
24.REMOVE STRAIGHT PIN
Perform this procedure only when replacement of the straight pin is necessary.
Remove the 2 straight pins.
15104
25.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 3 bolts and oil strainer sub-assembly from the timing chain cover sub-assembly.
Remove the oil strainer gasket from the oil strainer sub-assembly.
16321
26.REMOVE WATER INLET
16331A
27.REMOVE THERMOSTAT
16100
28.REMOVE ENGINE WATER PUMP ASSEMBLY
15601
29.REMOVE OIL FILTER SUB-ASSEMBLY
15671
30.REMOVE OIL FILTER BRACKET
Remove the 3 bolts and oil filter bracket.
Remove the oil filter bracket gasket from the timing chain cover sub-assembly.
11302R
31.REMOVE TIMING GEAR COVER TIGHT PLUG
32.SET NO. 1 CYLINDER TO TDC/EXHAUST
13471
33.REMOVE CRANKSHAFT PULLEY
34.REMOVE TIMING CHIN CIVER DRAIN COCK PLUG
Remove the timing chain cover drain cock plug and gasket from the timing chain cover sub-assembly.
11310
35.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
12205B
36.REMOVE VENTILATION CASE SUB-ASSEMBLY
Remove the 2 bolts and ventilation case sub-assembly from the timing chain cover sub-assembly.
37.REMOVE STUD BOLT
Perform this procedure only when replacement of the stud bolt is necessary.
Remove the stud bolt from the timing chain cover sub-assembly.
11302A
38.REMOVE TIMING CHAIN COVER OIL SEAL
| *a | Protective Tape |
| *b | Wooden Block |
Using a wooden block and a screwdriver with its tip wrapped with protective tape, pry out the timing chain cover oil seal.
13540
39.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Stopper Plate |
Turn the stopper plate of the No. 1 chain tensioner assembly clockwise to release the lock and push in the plunger.
| *a | Hexagon Wrench |
| *b | Stopper Plate |
Turn the stopper plate counterclockwise to set the lock, and insert a 3 mm hexagon wrench into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder block sub-assembly.
Remove the chain tensioner gasket from the No. 1 chain tensioner assembly.
13591
40.REMOVE TIMING CHAIN TENSION ARM
Remove the bolt and timing chain tensioner arm from the cylinder block sub-assembly.
13506
41.REMOVE CHAIN SUB-ASSEMBLY
Remove the chain sub-assembly.
13566B
42.REMOVE TIMING CHAIN GUIDE
Remove the 2 bolts and timing chain guide from the cylinder head sub-assembly and cylinder block sub-assembly.
13521
43.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket from the crankshaft.
13411C
44.REMOVE CRANKSHAFT STRAIGHT PIN
Remove the crankshaft straight pin from the crankshaft groove.
45.REMOVE BRACKET
Remove the bolt and bracket from the No. 3 camshaft bearing cap.
13520
46.REMOVE CAMSHAFT TIMING SPROCKET ASSEMBLY
|
Turn |
Rotate the crankshaft 90° clockwise.
Do not allow a lifted valve and piston to come into contact with each other when removing the camshaft.
| *a | Turn |
| *b | Hold |
Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt from the camshaft.
Remove the camshaft timing sprocket assembly from the camshaft.
13070A
47.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *a | Turn |
| *b | Hold |
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt from the No. 2 camshaft.
Remove the camshaft timing exhaust gear assembly from the No. 2 camshaft.
48.REMOVE CAMSHAFT BEARING CAP
| *1 | No. 1 Camshaft Bearing Cap |
| *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap |
Remove the 15 bolts in the order shown in the illustration.
Remove the No. 1 camshaft bearing cap, 5 No. 2 camshaft bearing caps and No. 3 camshaft bearing cap.
15678A
49.REMOVE OIL CONTROL VALVE FILTER
Remove the oil control valve filter from the No. 1 camshaft bearing cap.
13512
50.REMOVE NO. 2 CAMSHAFT
Remove the No. 2 camshaft from the cylinder head sub-assembly.
13511
51.REMOVE CAMSHAFT
Remove the camshaft from the cylinder head sub-assembly.
11381
52.REMOVE REAR ENGINE OIL SEAL RETAINER
Remove the 4 bolts and rear engine oil seal retainer from the cylinder block sub-assembly.
11381A
53.REMOVE REAR ENGINE OIL SEAL
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.
54.REMOVE STUD BOLT
Perform this procedure only when replacement of the stud bolt is necessary.
Using an E6 "TORX" socket wrench, remove the stud bolt from the rear engine oil seal retainer.
13751
55.REMOVE VALVE LIFTER
Remove the 12 valve lifters from the cylinder head sub-assembly.
Make a note of the inscribed mark on the valve lifters for each valve after removing them.
Arrange the valve lifters for each cylinder in the correct order.
11101
56.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11115
57.REMOVE CYLINDER HEAD GASKET
11445
58.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the cylinder block water jacket spacer LH and cylinder block water jacket spacer RH from the cylinder block sub-assembly.