Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P013623  O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low  P013624  O2 (A/F) Sensor Circuit Bank 1 Sensor 2 Signal Stuck High  


DESCRIPTION

Refer to DTC P013611.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P013611

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P013623 O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low

Heated oxygen sensor (sensor 2) is stuck lean:

Air-fuel ratio of heated oxygen sensor (sensor 2) does not change when integrated air mass flow amount reaches 0.025 kg during active air fuel ratio control even when vehicle is driven in an urban area with many hills for approximately 20 minutes or more (3 trip detection logic).



·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Fuel pressure

·

Fuel injector assembly

·

Gas leakage from exhaust system


Comes on DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B
P013624 O2 (A/F) Sensor Circuit Bank 1 Sensor 2 Signal Stuck High

Heated oxygen sensor (sensor 2) is stuck rich:

Output voltage of heated oxygen sensor (sensor 2) does not become lower than 0.25 V even though fuel-cut is performed continuously until integrated oxygen reaches 1500 mg or more when vehicle is driven in an urban area with many hills for approximately 20 minutes or more (3 trip detection logic).



·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Fuel pressure

·

Fuel injector assembly

·

Gas leakage from exhaust system


Comes on DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P013623 and P013624 are detected when the vehicle is driven in an urban area with many hills for approximately 20 minutes or more.

CAUTION / NOTICE / HINT

HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P013623 OR P013624)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P013623 or P013624 is output A
P013623 or P013624 and other DTCs are output B


HINT:

If any DTCs other than P013623 or P013624 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Warm up the engine at an engine speed of 2500 rpm for approximately 3 minutes.


Procedure1

b.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Injection Volume
O2 Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 277,1305,218

c.

Monitor the voltage output of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) (O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
The heated oxygen sensors reacts in accordance with increases and decreases of the fuel injection volume:
+12.5% = Rich output:

Higher than 0.55 V

-12.5% = Lean output:

Below 0.4 V


A318964E03
0.135,0.385 0.75,0.583 0.615,0.198 10 false Case 0.24,1.875 0.854,2.073 0.615,0.198 10 false 1 0.25,4.031 0.865,4.229 0.615,0.198 10 false 2 0.25,6.281 0.865,6.479 0.615,0.198 10 false 3 0.75,0.25 2.385,0.75 1.635,0.5 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 2.844,0.25 4.5,0.708 1.656,0.458 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5,0.417 7.031,0.833 2.031,0.417 10 false Main Suspected Trouble Area 0.656,1 1.917,1.302 1.26,0.302 10 false Injection Volume 2.667,1 3.927,1.302 1.26,0.302 10 false Injection Volume 2.615,3.083 3.875,3.385 1.26,0.302 10 false Injection Volume 0.583,3.083 1.844,3.385 1.26,0.302 10 false Injection Volume 0.656,5.167 1.917,5.469 1.26,0.302 10 false Injection Volume 2.656,5.167 3.917,5.469 1.26,0.302 10 false Injection Volume 0.844,1.25 1.521,1.552 0.677,0.302 8 false +12.5% 3.01,1.25 3.604,1.583 0.594,0.333 8 false +12.5% 3.031,3.333 4.292,3.635 1.26,0.302 8 false +12.5% 0.844,3.333 2.104,3.635 1.26,0.302 8 false +12.5% 0.854,1.542 1.49,1.917 0.635,0.375 8 false -12.5% 3.031,1.5 4.292,1.802 1.26,0.302 8 false -12.5% 0.865,3.583 2.125,3.885 1.26,0.302 8 false -12.5% 3.052,3.583 3.75,4 0.698,0.417 8 false -12.5% 3.115,5.927 4.375,6.229 1.26,0.302 8 false -12.5% 0.958,5.938 2.219,6.24 1.26,0.302 8 false -12.5% 0.938,5.719 2.198,6.021 1.26,0.302 8 false +12.5% 3.083,5.646 4.344,5.948 1.26,0.302 8 false +12.5% 0.667,1.833 1.927,2.135 1.26,0.302 10 false Output Voltage 2.74,4 4,4.302 1.26,0.302 10 false Output Voltage 0.667,4 1.927,4.302 1.26,0.302 10 false Output Voltage 0.74,6.365 2,6.667 1.26,0.302 10 false Output Voltage 2.698,6.333 3.958,6.635 1.26,0.302 10 false Output Voltage 0.75,4.323 1.479,4.688 0.729,0.365 8 false Higher than 0.55 V 0.813,2.281 1.448,2.833 0.635,0.552 8 false Higher than 0.55 V 2.667,1.833 3.927,2.135 1.26,0.302 10 false Output Voltage 2.635,2.302 3.708,2.667 1.073,0.365 8 false Higher than 0.55 V 2.958,2.563 4.219,2.865 1.26,0.302 8 false Below 0.4 V 0.615,4.656 1.875,4.958 1.26,0.302 8 false Below 0.4 V 0.729,2.583 1.563,2.885 0.833,0.302 8 false Below 0.4 V 2.635,4.521 4.188,4.917 1.552,0.396 8 false Almost no reaction 2.677,6.875 4.115,7.125 1.438,0.25 8 false Almost no reaction 0.729,6.802 1.25,7.167 0.521,0.365 8 false Almost no reaction 2.01,4.552 2.344,4.865 0.333,0.313 10 false OK 2.115,2.448 2.448,2.76 0.333,0.313 10 false OK 4.344,2.427 4.677,2.74 0.333,0.313 10 false OK 4.323,4.51 4.656,4.823 0.333,0.313 10 false NG 4.344,6.875 4.677,7.188 0.333,0.313 10 false NG 2.115,6.865 2.448,7.177 0.333,0.313 10 false NG 5.896,1.865 6.229,2.177 0.333,0.313 10 false - 4.948,3.938 6.49,4.406 1.542,0.469 10 false - Heated oxygen sensor (Sensor 2) 4.917,5.167 6.875,5.563 1.958,0.396 10 false - Extremely rich or lean actual air fuel ratio 4.917,5.573 6.875,5.969 1.958,0.396 10 false - Fuel injector assembly leak or blockage 4.917,5.979 6.99,6.229 2.073,0.25 10 false - Gas leak from exhaust system 4.917,6.219 6.875,6.615 1.958,0.396 10 false - Ignition system 4.917,6.469 6.875,6.865 1.958,0.396 10 false - Fuel pressure 4.917,6.719 6.646,7.167 1.729,0.448 10 false - Manifold absolute pressure sensor 4.917,7.135 6.667,7.594 1.75,0.458 10 false - Engine coolant temperature sensor

The following procedure enables the technician to check and graph the voltage outputs of both the heated oxygen sensors.

To display the graph, enter the following menus:

Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; then press the view button.

HINT:

If the vehicle is short of fuel, the air fuel ratio becomes lean and the heated oxygen sensor DTCs are recorded, and then the MIL illuminates.


Result:
Result Proceed to
Case 2 A
Case 3 B
Case 1 C



Post-procedure1

d.

None.



A

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

B

7.CHECK WHETHER MISFIRE OCCURS

C

10.CLEAR DTC
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D85-4 (OX1B) - D50-124 (OX1B) Always Below 1 Ω
D85-2 (HT1B) - D50-24 (HT1B) Always Below 1 Ω
D85-3 (E1) - D50-123 (E12) Always Below 1 Ω
D85-4 (OX1B) or D50-124 (OX1B) - Body ground Always 10 kΩ or higher
D85-2 (HT1B) or D50-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013623 OR P013624)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013623 OR P013624)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTC P013623 or P013624 is output B


Post-procedure1

d.

None.



A

END

B

7.CHECK WHETHER MISFIRE OCCURS
7.CHECK WHETHER MISFIRE OCCURS
a.

Check the idling condition.

OK:

Rough idling does not occur.



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL PRESSURE

NG

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

9.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

OK

CHECK FOR EXHAUST GAS LEAK

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P013623 OR P013624)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P013623 OR P013624)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P013623 or P013624 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B