Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P003611  HO2S Heater Control Circuit Low Bank 1 Sensor 2 Circuit Short to Ground  P003612  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery  P003614  HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P013611.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P013611

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The heated oxygen sensor (sensor 2) heater circuit uses a relay on the +B side of the circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P003611 HO2S Heater Control Circuit Low Bank 1 Sensor 2 Circuit Short to Ground Short to ground in heated oxygen sensor heater (sensor 2) circuit (3 trip detection logic)
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on DTC stored Engine A
P003612 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery Short to battery in heated oxygen sensor heater (sensor 2) circuit (3 trip detection logic)
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on DTC stored Engine A
P003614 HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open Open in heated oxygen sensor heater (sensor 2) circuit (3 trip detection logic)
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

DTC P003611, P003612 and P003614 are detected when the engine idles for approximately 20 minutes.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (SENSOR 2) (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D87-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - EFI-MAIN NO. 1 RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D85-2 (HT1B) - D50-24 (HT1B) Always Below 1 Ω
D85-2 (HT1B) or D50-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003611, P003612 OR P003614)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003611, P003612 OR P003614)

Pre-procedure1

a.

Start the engine.


b.

Allow the engine to idle for 20 minutes or more.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
P003611, P003612 or P003614 is output B


Post-procedure1

d.

None.



A

B

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - EFI-MAIN NO. 1 RELAY)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - D85-1 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) or D85-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR