Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model LHD) › 2020.07–2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432271 BRAKE BOOSTER(for Gasoline Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model LHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



b.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



c.
C436798N01
0.75,0.208 0.948,0.406 0.198,0.198 10 true 3 0.677,1.875 0.875,2.073 0.198,0.198 10 true 1 2.563,0.25 2.76,0.448 0.198,0.198 10 true 2 2.552,1.844 2.75,2.042 0.198,0.198 10 true 4

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the 4 nuts in the order shown in the illustration.



d.
C436805C01
1.719,2.365 2.031,2.563 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




e.
C436796

Engage the 5 clamps to install a new No. 2 brake tube clamp to the brake lines.


f.
C436795

Engage the clamp and install a new No. 1 brake tube clamp to the vehicle body.


g.
C436794

Engage the 5 clamps to install the brake lines to the No. 1 brake tube clamp.


h.

Remove the protective tape.


i.

w/ Vacuum Warning Switch:

i.

Connect the vacuum warning switch connector.



j.

w/ Vacuum Sensor:

i.

Connect the vacuum sensor connector.



k.

Engage the clamp.


l.

Install the engine room main wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Hide 45260 5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 6.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 55606 7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 44773F 8.CONNECT UNION TO CHECK VALVE HOSE (for M15A-FKS)

a.
C436789C01
1.115,0.698 1.219,0.698 1.219,0.698 1.719,1.063 true 0.906,0.604 1.073,0.771 0.167,0.167 10 true *a
*a Paint Mark


Connect the union to check valve hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the union to check valve hose, face the paint mark up.

·

Make sure that the tabs of the clip are facing upward.




Hide 44772 9.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for 1KR-FE)

a.
C436790C01
2.219,0.958 2.323,0.958 2.323,0.958 2.521,1.563 true 2.021,0.865 2.198,1.031 0.177,0.167 10 true *a
*a Paint Mark


Install the vacuum hose assembly to the vehicle body with the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


b.

Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, make sure that the paint mark is facing the front of the vehicle.

·

Make sure that the tabs of the clip are facing the front of the vehicle.




Hide 55225C 10.INSTALL DASH PANEL HEAT INSULATOR (for M15A-FKS)

a.

Install dash panel heat insulator to the vehicle body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51451A 11.INSTALL CENTER ENGINE UNDER COVER (for M15A-FKS)

Hide 14.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 47201 16.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY