When the rear window defogger switch on the No. 1 heater control sub-assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly and power distribution box assembly via LIN communication. When the power distribution box assembly receives the signal, it turns on the DEF relay to operate the window defogger system.
An operation request signal is sent to the air conditioning amplifier assembly via LIN communication when the rear window defogger switch (air conditioning control assembly) is operated. When the air conditioning amplifier assembly receives the signal, it sends an operation request signal via CAN communication to the main body ECU (multiplex network body ECU).When the main body ECU (multiplex network body ECU) receives the signal, it sends an operation request signal via CPXI communication to the power distribution box assembly. After the operation request signal is received by the power distribution box assembly it outputs an operation signal and operates the window defogger.
Inspect the fuses for circuits related to this system before performing the following procedure.
With the negative (-) battery terminal connected, disconnect/do not connect the connector of the power distribution box assembly.
When replacing the power distribution box assembly, the system may not operate normally if the same part number is not used.
The window defogger system uses the CAN communication system, LIN communication system and CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Troubleshoot the window defogger system after confirming that the communication system is functioning properly.*1
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
*1: for Automatic Air Conditioning System
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Defogger Input Signal | Window defogger switch signal input condition | ON or OFF | ON: Rear window defogger switch is on
OFF: Rear window defogger switch is off |
- |
| Tester Display |
|---|
| Rear Defogger Input Signal |
The Data List value displays "ON" with the rear window defogger switch set to ON.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Air Conditioning System) | B |
| NG (for Manual Air Conditioning System) | C |
A
B
C
Using the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Defogger Output Signal | Window defogger output condition | ON or OFF | ON: Window defogger operates
OFF: Window defogger does not operate |
- |
| Tester Display |
|---|
| Rear Defogger Output Signal |
When the rear window defogger switch is ON, the data monitor standard value is "ON".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the 4E power distribution box assembly connector.
Disconnect the X3 rear window defogger wire (back door glass) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4E-43 - X3-1 (B) | Always | Below 1 Ω |
| 4E-43 or X3-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Y9 rear window defogger wire (back door glass) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Y9-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 5 Door: Click hereVehicle Exterior>WINDOW / GLASS>BACK DOOR GLASS (for 5 Door)>REMOVAL
for 3 Door: Click hereVehicle Exterior>WINDOW / GLASS>BACK DOOR GLASS (for 3 Door)>REMOVAL
NG
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for HV Model) | B |
| NG (for Gasoline Model) | C |
A
B
C
Check that the defogger indicator illuminates when the window defogger switch is on.
Defogger indicator illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range |
|---|---|---|
| Rear Defogger Relay | Rear window defogger wire (Back door glass) | OFF or ON |
| Tester Display |
|---|
| Rear Defogger Relay |
Rear window defogger wire (back door glass) warms up.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (except G16E-GTS) | B |
| NG (for G16E-GTS) | C |
A
B
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER (except G16E-GTS)>REMOVAL
C
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER (for G16E-GTS)>REMOVAL
Disconnect the 4C power distribution box assembly connector.
Disconnect the H56 No. 1 heater control sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-24 - H56-6 (RDEF) | Always | Below 1 Ω |
| 4C-24 or H56-6 (RDEF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H56-5 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H56-2 (ERDF) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG