Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P006D62  Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 1 Signal Compare Failure  


DESCRIPTION

The E.F.I. vacuum sensor assembly is installed upstream of the turbocharger compressor and measures the air inlet duct internal pressure with a built-in sensor.

At ignition switch to ON or during idling, the E.F.I. vacuum sensor assembly and the atmospheric pressure sensor built into the ECM are at atmospheric pressure and their output match.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P006D62 Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 1 Signal Compare Failure Either of the following conditions is met (1 trip detection logic):
·

At ignition switch to ON or during idling, if the difference in atmospheric pressure values is the threshold or greater when the output values from the E.F.I. vacuum sensor assembly and the atmospheric pressure sensor are compared.

·

The deviation between the air cleaner pressure loss calculated from the atmospheric pressure and E.F.I. vacuum sensor assembly and the air cleaner pressure loss estimated from the mass air flow meter sub-assembly is at the threshold or higher.


·

E.F.I. vacuum sensor assembly

·

Mass air flow meter sub-assembly

·

Wire harness or connector

·

Intake system

·

ECM


- SAE: P006D

MONITOR DESCRIPTION

At ignition switch to ON or during idling, if the difference in atmospheric pressure values is the threshold or greater when the output values from the E.F.I. vacuum sensor assembly and the atmospheric pressure sensor built into the ECM are compared, or if the deviation between the air cleaner pressure loss calculated from the atmospheric pressure and E.F.I. vacuum sensor assembly and the air cleaner pressure loss estimated from the mass air flow meter sub-assembly is at the threshold or higher while driving (example: when the intake air volume is 40 gm/sec, the value obtained by subtracting the atmospheric pressure from the E.F.I. vacuum sensor assembly value is larger than 7.5 kPa [1.09 psi]or less than -9.2 kPa [-1.33 psi]), the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A414226E02
0.719,0.677 1.469,0.896 0.75,0.219 10 false 40 km/h 0.885,2.167 1.406,2.406 0.521,0.24 10 false Idling 0.375,2.51 1.302,2.896 0.927,0.385 10 false Ignition switch ON 1.677,3.208 2.906,3.458 1.229,0.25 10 false 5 seconds or more 5.458,3.354 5.896,3.677 0.438,0.323 10 false [D] 3.573,3.219 4.802,3.469 1.229,0.25 10 false 5 seconds or more 1.604,2.344 2.125,2.583 0.521,0.24 10 false [A] 2.177,2.073 2.698,2.313 0.521,0.24 10 false [B] 4.052,0.51 4.573,0.75 0.521,0.24 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and wait 5 seconds or more [B].

7.

Drive the vehicle at 40 km/h (25 mph) for 5 seconds or more [C].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P006D62.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P012A11 for the E.F.I. vacuum sensor assembly circuit.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>P012A11

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P006D62)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P006D62 is output A
P006D62 and other DTCs are output B


HINT:

If any DTCs other than P006D62 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK1 AND ATMOSPHERIC PRESSURE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK1 AND ATMOSPHERIC PRESSURE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Turbocharger/Supercharger Inlet Pressure Bank1
50003 372 229,791

b.

Compare Turbocharger/Supercharger Inlet Pressure Bank1 and Atmospheric Pressure in the Data List.


Result:
Result Proceed to
Difference between Turbocharger/Supercharger Inlet Pressure Bank1 and Atmospheric Pressure in the Data List exceeds 7.1 kPa [1.03 psi] A
Other than above B



A

3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

B

7.CHECK INTAKE SYSTEM
3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
50003 372 229

b.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

A337505

HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) [14.65 psi(abs)].

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa [0.15 psi]. This varies by weather.




c.

Compare the Atmospheric pressure value in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following A
Difference between Atmospheric Pressure in the Data List and normal atmospheric pressure value is 10 kPa (1.45 psi) or more. B




A

4.CLEAR DTC

B

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.READ OUTPUT DTC
5.READ OUTPUT DTC
a.

Remove the E.F.I. vacuum sensor assembly, switch bank 1, and then install the E.F.I. vacuum sensor assembly.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
A bank DTC different from the one shown in step 1 is output A
Other than above B



A

REPLACE E.F.I. VACUUM SENSOR ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D104-82(VCPC) Always Below 1 Ω
D93-2(PIC) - D104-105(PIC) Always Below 1 Ω
D93-1(E2) - D104-81(EPIC) Always Below 1 Ω
D93-3(VC) or D104-82(VCPC) - Body ground and other terminals Always 10 kΩ or higher
D93-2(PIC) or D104-105(PIC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INTAKE SYSTEM
a.

Check that there is no air suction or blockage at any points in the intake system.

Click hereEngine / Hybrid System>G16E-GTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No air suction or blockage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

9.INSPECT E.F.I. VACUUM SENSOR ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR
9.INSPECT E.F.I. VACUUM SENSOR ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

12.CHECK HARNESS AND CONNECTOR
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P006D62)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P006D62)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P006D62.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P006D62 is output)
B




A

END

B

12.CHECK HARNESS AND CONNECTOR
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-1(E2) Ignition switch ON 4.5 to 5.5 V
D93-2(PIC) - D93-1(E2) Ignition switch ON 3.0 to 5.5 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D93-2(PIC) Ignition switch off 171 to 189 kΩ
D93-1(E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE E.F.I. VACUUM SENSOR ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
13.CHECK HARNESS AND CONNECTOR (E.F.I. VACUUM SENSOR ASSEMBLY - ECM)
a.

Disconnect the E.F.I. vacuum sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D93-3(VC) - D104-82(VCPC) Always Below 1 Ω
D93-2(PIC) - D104-105(PIC) Always Below 1 Ω
D93-1(E2) - D104-81(EPIC) Always Below 1 Ω
D93-3(VC) or D104-82(VCPC) - Body ground and other terminals Always 10 kΩ or higher
D93-2(PIC) or D104-105(PIC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D23-3(VCC) - D23-2(E2G) Ignition switch ON 4.8 to 5.2 V
D23-1(FG) - D23-2(E2G) Ignition switch ON 4.8 to 5.2 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-3(VCC) - D23-1(FG) Ignition switch off 2.09 to 2.31 kΩ
D23-2(E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-3(VCC) - D104-84(VCVG) Always Below 1 Ω
D23-1(FG) - D104-107(VG) Always Below 1 Ω
D23-2(E2G) - D104-83(E2G) Always Below 1 Ω
D23-3(VCC) or D104-84(VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-1(FG) or D104-107(VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR