Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › from 2020.09
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0447531 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.
C445891

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Tighten the bolt with the nut secured.




b.

Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
150 N*m (1530 kgf*cm, 111 ft.*lbf)


Hide 2.INSTALL FLEXIBLE HOSE BRACKET

a.

Install the flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48720A 3.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48258C 4.INSTALL REAR LOWER COIL SPRING INSULATOR

Hide 48790 7.FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Tighten the bolt with the nut secured.



Hide 48720A 8.FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48740F 9.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48540 10.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

Hide 11.INSTALL REAR BRAKE

a.

Install the rear brake to the rear axle carrier sub-assembly with the nut.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 48840A 12.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 42450B 13.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 16.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 42491 17.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42312B 19.INSTALL REAR AXLE SHAFT NUT

a.

Clean the threaded parts on the rear drive shaft assembly and a new rear axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new rear drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm socket wrench, install the rear axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

NOTICE:

Stake the rear axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Depress the brake pedal to prevent the drive shaft from rotating.



c.
C445879

Using a chisel and hammer, stake the rear axle shaft nut.


Hide 20.INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL

Hide 21.INSTALL REAR WHEEL

Hide 48740F 22.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION