Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.09–2021.11
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  System Malfunction Message is Displayed on the Multi-information Display  


SYSTEM DESCRIPTION

If an abnormal operation that may lead to a malfunction of the steering lock ECU (steering lock actuator or upper bracket assembly), or abnormal vehicle speed information is detected by the certification ECU (smart key ECU assembly), a system malfunction message is displayed on the multi-information display.

WIRING DIAGRAM

for CVT


E443722E05
5.583,6.323 7.125,6.802 1.542,0.479 10 false Certification ECU (Smart Key ECU Assembly) 0.063,2.042 2.896,2.5 2.833,0.458 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.073,1.885 0.875,2.156 0.802,0.271 10 false H71 1.75,0.427 2.552,0.698 0.802,0.271 10 false B 1.958,0.323 2.76,0.594 0.802,0.271 10 false 7 3.344,0.396 5.021,0.615 1.677,0.219 10 false from Auxiliary Battery 2.354,0.719 3.417,1.073 1.063,0.354 10 false AM1*2 1.635,0.938 2.438,1.208 0.802,0.271 10 false IGE 1.969,0.854 2.771,1.125 0.802,0.271 10 false 3 1.594,1.469 2.396,1.74 0.802,0.271 10 false GND 1.969,1.344 2.771,1.615 0.802,0.271 10 false 1 5.896,0.969 6.698,1.24 0.802,0.271 10 false SLR+ 5.896,1.458 6.698,1.729 0.802,0.271 10 false E 5.552,0.771 6.354,1.042 0.802,0.271 10 false 24 5.552,1.271 6.354,1.542 0.802,0.271 10 false 29 5.531,0.969 6.333,1.24 0.802,0.271 10 false H46 5.51,1.458 6.313,1.729 0.802,0.271 10 false H46 6.552,3.594 6.729,3.875 0.177,0.281 10 false IC 6.229,2.948 6.49,3.26 0.26,0.313 10 false +B 5.5,3.417 6.302,3.688 0.802,0.271 10 false H45 5.51,5.896 6.313,6.167 0.802,0.271 10 false H45 5.885,3.313 6.688,3.583 0.802,0.271 10 false STAR 5.896,5.885 6.698,6.156 0.802,0.271 10 false STA 5.594,3.219 6.396,3.49 0.802,0.271 10 false 10 5.583,5.688 6.385,5.958 0.802,0.271 10 false 3 0.646,6.469 1.188,6.76 0.542,0.292 10 false ECM 1.792,5.125 4.302,5.542 2.51,0.417 10 false Park/Neutral Position Switch 1.792,4.958 2.594,5.229 0.802,0.271 10 false D45 2.625,3.854 3.427,4.125 0.802,0.271 10 false 4 3.229,4.563 4.031,4.833 0.802,0.271 10 false 5 0.875,3.406 1.677,3.677 0.802,0.271 10 false NSW 0.938,5.875 1.74,6.146 0.802,0.271 10 false STA 1.323,3.281 2.125,3.552 0.802,0.271 10 false 23 1.323,5.75 2.125,6.021 0.802,0.271 10 false 30 2.125,4.479 2.927,4.75 0.802,0.271 10 false P 2.521,4.188 3.323,4.458 0.802,0.271 10 false B 2.906,4.188 3.708,4.458 0.802,0.271 10 false L 2.125,4.75 2.927,5.021 0.802,0.271 10 false N 0.667,6.313 1.146,6.51 0.479,0.198 10 false A54 2.115,0.542 3.177,0.896 1.063,0.354 10 false STRG LOCK*1 1.031,6.99 2.365,7.208 1.333,0.219 10 false *1: for TMMF Made 1.042,7.302 2.375,7.521 1.333,0.219 10 false *2: for TMC Made


for Manual Transaxle with 1KR-FE


E446703E03
5.583,6.323 7.125,6.781 1.542,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.052,2.031 2.885,2.563 2.833,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.073,1.885 0.875,2.156 0.802,0.271 10 false H71 1.75,0.427 2.552,0.698 0.802,0.271 10 false B 1.958,0.323 2.76,0.594 0.802,0.271 10 false 7 3.344,0.406 4.833,0.729 1.49,0.323 10 false from Auxiliary Battery 2.115,0.563 3.177,0.917 1.063,0.354 10 false STRG LOCK 1.635,0.938 2.438,1.208 0.802,0.271 10 false IGE 1.969,0.854 2.771,1.125 0.802,0.271 10 false 3 1.594,1.469 2.396,1.74 0.802,0.271 10 false GND 1.969,1.344 2.771,1.615 0.802,0.271 10 false 1 5.896,0.948 6.698,1.219 0.802,0.271 10 false SLR+ 5.896,1.458 6.698,1.729 0.802,0.271 10 false E 5.563,0.75 6.365,1.021 0.802,0.271 10 false 24 5.563,1.25 6.365,1.521 0.802,0.271 10 false 29 5.51,0.938 6.313,1.208 0.802,0.271 10 false H46 5.51,1.438 6.313,1.708 0.802,0.271 10 false H46 6.552,3.594 6.729,3.875 0.177,0.281 10 false IC 6.229,2.948 6.49,3.26 0.26,0.313 10 false +B 5.51,3.385 6.313,3.656 0.802,0.271 10 false H45 5.521,5.865 6.323,6.135 0.802,0.271 10 false H45 5.875,3.292 6.677,3.563 0.802,0.271 10 false STAR 5.896,5.885 6.698,6.156 0.802,0.271 10 false STA 5.563,3.198 6.365,3.469 0.802,0.271 10 false 10 5.583,5.688 6.385,5.958 0.802,0.271 10 false 3 0.635,6.313 1.229,6.531 0.594,0.219 10 false ECM 2.385,4.854 4.625,5.167 2.24,0.313 10 false Clutch Start Switch Assembly 2.396,4.708 3.198,4.979 0.802,0.271 10 false A64 3.802,4.438 4.604,4.708 0.802,0.271 10 false 1 0.875,3.396 1.677,3.667 0.802,0.271 10 false NSW 0.938,5.865 1.74,6.135 0.802,0.271 10 false STA 1.344,3.208 2.146,3.479 0.802,0.271 10 false 111 1.344,5.865 2.146,6.135 0.802,0.271 10 false A55 3.083,4.448 3.885,4.719 0.802,0.271 10 false B 3.594,4.448 4.396,4.719 0.802,0.271 10 false L 2.875,4.438 3.677,4.708 0.802,0.271 10 false 2 1.333,3.406 2.135,3.677 0.802,0.271 10 false D50 1.385,5.667 2.188,5.938 0.802,0.271 10 false 46


for Manual Transaxle without 1KR-FE


B575810E06
5.583,6.323 7.125,6.781 1.542,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.052,2.031 2.885,2.563 2.833,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.073,1.885 0.875,2.156 0.802,0.271 10 false H71 1.75,0.427 2.552,0.698 0.802,0.271 10 false B 1.958,0.323 2.76,0.594 0.802,0.271 10 false 7 3.344,0.406 4.833,0.729 1.49,0.323 10 false from Auxiliary Battery 2.344,0.74 3.406,1.094 1.063,0.354 10 false AM1*2 1.635,0.938 2.438,1.208 0.802,0.271 10 false IGE 1.969,0.854 2.771,1.125 0.802,0.271 10 false 3 1.594,1.469 2.396,1.74 0.802,0.271 10 false GND 1.969,1.344 2.771,1.615 0.802,0.271 10 false 1 5.896,0.948 6.698,1.219 0.802,0.271 10 false SLR+ 5.896,1.458 6.698,1.729 0.802,0.271 10 false E 5.563,0.75 6.365,1.021 0.802,0.271 10 false 24 5.563,1.25 6.365,1.521 0.802,0.271 10 false 29 5.51,0.938 6.313,1.208 0.802,0.271 10 false H46 5.51,1.438 6.313,1.708 0.802,0.271 10 false H46 6.552,3.594 6.729,3.875 0.177,0.281 10 false IC 6.229,2.948 6.49,3.26 0.26,0.313 10 false +B 5.51,3.385 6.313,3.656 0.802,0.271 10 false H45 5.521,5.865 6.323,6.135 0.802,0.271 10 false H45 5.875,3.292 6.677,3.563 0.802,0.271 10 false STAR 5.896,5.885 6.698,6.156 0.802,0.271 10 false STA 5.594,3.219 6.396,3.49 0.802,0.271 10 false 10 5.583,5.688 6.385,5.958 0.802,0.271 10 false 3 0.656,6.51 1.25,6.729 0.594,0.219 10 false ECM 2.385,4.854 4.625,5.167 2.24,0.313 10 false Clutch Start Switch Assembly 2.396,4.708 3.198,4.979 0.802,0.271 10 false A64 3.802,4.438 4.604,4.708 0.802,0.271 10 false 1 0.875,3.396 1.677,3.667 0.802,0.271 10 false NSW 0.938,5.865 1.74,6.135 0.802,0.271 10 false STA 1.354,3.271 2.156,3.542 0.802,0.271 10 false 23 1.333,5.74 2.135,6.01 0.802,0.271 10 false 30 3.083,4.448 3.885,4.719 0.802,0.271 10 false B 3.594,4.448 4.396,4.719 0.802,0.271 10 false L 0.646,6.313 1.708,6.573 1.063,0.26 10 false A54*3, A106*4 2.875,4.438 3.677,4.708 0.802,0.271 10 false 2 2.125,0.552 3.563,0.885 1.438,0.333 10 false STRG LOCK*1, *4 0.073,7.292 2.76,7.573 2.688,0.281 10 false *1: for TMMF Made with M15A-FKS 4.573,7.292 5.938,7.583 1.365,0.292 10 false *3: for M15A-FKS 5.792,7.292 7.156,7.583 1.365,0.292 10 false *4: for G16E-GTS 2.365,7.292 5.052,7.573 2.688,0.281 10 false *2: for TMC Made with M15A-FKS


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output A
DTC is output. B



A

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)

B

GO TO ENTRY AND START SYSTEM (for Entry Function) (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sensor Malfunction History History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B278196 is stored) OK or NG OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.
NG: History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.)
When NG is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Sensor Malfunction History
50003 440 48
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (NEUTRAL SWITCH / CLUTCH SWITCH)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

3.READ VALUE USING GTS (NEUTRAL SWITCH / CLUTCH SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch
for CVT

Shift position (P and N)


for Manual Transaxle

State of clutch pedal


OFF or ON
for CVT

OFF: Shift lever in any position other than P or N

ON: Shift lever in P or N


for Manual Transaxle

OFF: Clutch pedal released

ON: Clutch pedal depressed


for CVT
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


for Manual Transaxle
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever or clutch pedal operation.



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

4.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))

B

9.INSPECT PARK/NEUTRAL POSITION SWITCH

C

11.INSPECT CLUTCH START SWITCH ASSEMBLY
4.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Running Condition (Line) Vehicle being driven or stopped Stop or Driving Stop: Vehicle stopped
Driving: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Running Condition (Line)
50003 454 402
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Result Proceed to
OK A
NG (for TMC Made) B
NG (for TMMF Made) C



A

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

C

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.

Disconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C435465C01
1.5,1.031 1.917,1.281 0.417,0.25 0.958,1.667 1.208,1.667 1.208,1.667 1.208,2.417 true 2.458,1.667 2.208,1.667 2.208,1.667 2.208,2.417 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.583,1.063 1.896,1.219 0.313,0.156 10 false H71 0.625,1.583 1.104,1.781 0.479,0.198 10 false GND 2.5,1.583 2.813,1.74 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
B518305C11
1.49,0.99 1.896,1.25 0.406,0.26 2.354,2.885 1.885,2.885 1.885,2.885 1.885,1.979 true 2.719,2.677 2.25,2.677 2.25,2.677 2.25,1.99 true 0.188,0.281 0.5,0.438 0.313,0.156 10 false *a 1.573,1.031 2.073,1.302 0.5,0.271 10 false H71 2.448,2.802 2.948,3.073 0.5,0.271 10 false IGE 2.781,2.604 3.281,2.875 0.5,0.271 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H71-3 (IGE) - H71-1 (GND)

Steering lock motor operating when all conditions met, and then door opened:

-

The steering is unlocked.

-

The ignition switch is off.

-

The shift lever is in P.*1



11 to 14 V → Below 1 V


*1: for CVT



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
7.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-3 (IGE) - H46-24 (SLR+) Always Below 1 Ω
H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C435466C01
1.49,0.938 1.906,1.198 0.417,0.26 2.344,2.948 1.896,2.948 1.896,2.948 1.896,1.969 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.385,2.844 2.792,3.01 0.406,0.167 10 false IGE 1.573,0.969 1.896,1.208 0.323,0.24 10 false H71
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H71-3 (IGE) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

9.INSPECT PARK/NEUTRAL POSITION SWITCH

OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH AND ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH AND ECM)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D45 park/neutral position switch connector.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - D45-5 (L) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-3 (STA) or D45-5 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or D45-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Disconnect the A54 ECM connector.*1


d.

Disconnect the A106 ECM connector.*2


e.

Disconnect the A55 and D50 ECM connector.*3


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A54-23 (NSW)*1 Always Below 1 Ω
H45-10 (STAR) - A106-23 (NSW)*2 Always Below 1 Ω
H45-10 (STAR) - D50-111 (NSW)*3 Always Below 1 Ω
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-3 (STA) or A64-1 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground*1 Always 10 kΩ or higher
H45-10 (STAR) or A106-23 (NSW) - Other terminals and body ground*2 Always 10 kΩ or higher
H45-10 (STAR) or D50-111 (NSW) - Other terminals and body ground*3 Always 10 kΩ or higher
H45-10 (STAR) or A64-2 (B) - Other terminals and body ground Always 10 kΩ or higher



*1: for M15A-FKS

*2: for G16E-GTS

*3: for 1KR-FE


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR