2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    Destination
    Engine
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    Except for Rough Road Package
    1KR-FE
    165/70R14 81S
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    240 (2.4, 35)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    250 (2.5, 36)
    230 (2.3, 33)
    2SZ-FE
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    230 (2.3, 33)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    250 (2.5, 36)
    240 (2.4, 35)
    1ND-TV
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    240 (2.4, 35)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    260 (2.7, 38)
    240 (2.4, 35)
    Rough Road Package
    1KR-FE
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    2SZ-FE
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    240 (2.4, 35)
    240 (2.4, 35)

  1. R003031E01
    Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less


ROTATE TIRES

C125265E05

HINT:
Rotate the tires, as shown in the illustration.


INSPECT WHEEL BALANCE

C080976E01
  1. Check and perform off-car balancing.

  1. If required, perform on-car balancing.

    Imbalance after adjustment:
    8 g (0.018 lb) or less


INSPECT FRONT AXLE HUB BEARING
  1. Remove the front wheel.

  1. Separate the front disc brake caliper (Click here).

  1. Remove the front disc (Click here).

  1. C130298
    Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the bearing.

  1. C130299
    Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout exceeds the maximum, replace the bearing and axle hub.

  1. Install the front disc (Click here).

  1. Install the front disc brake caliper (Click here).

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. for Rear Drum Brake:

    1. Remove the rear brake drum (Click here).

  1. for Rear Disc Brake:

    1. Disconnect the parking brake cable (Click here).

    2. Separate the rear disc brake caliper (Click here).

    3. Remove the rear disc (Click here).

  1. C130300E01
    Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.

  1. C130301E01
    Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. for Rear Drum Brake:

    1. Install the rear brake drum.

  1. for Rear Disc Brake:

    1. Install the rear disc (Click here).

    2. Install the rear disc brake caliper (Click here).

    3. Connect the parking brake cable (Click here).

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSPECTION (from Aug 2005)RECOVERY (from Nov 2005) →